Chainsaw attachments to increase the functionality of the tool: types, characteristics, photos and videos

The nozzle allows you to save money. Manufacturers produce many different models of garden tools. In order not to purchase each type separately, you can choose a special attachment. It helps equipment become multifunctional without spending large sums. The main thing is to install it correctly on the device.

@lizing-spectehniki.ru

Why are there different attachments for chainsaws?

Chainsaws are one of the most common motorized tools that almost every home craftsman living in a private home has. Such devices are equipped with high-power drive units capable of reaching shaft speeds of up to 12,000 rpm. These are colossal indicators, thanks to which chainsaws cope with sawing thick and durable wood trunks.

However, for most owners, such tools are used only a few times a year (mainly in autumn and spring), when collecting firewood or pruning fruit trees. The rest of the time, chainsaws lie idle in the garage. Although they can be used all year round, for which you only need to install the appropriate attachments instead of the tire with a chain. The use of such devices is determined by a number of the following factors:

  1. Great power of the unit, which allows you to perform very heavy work.
  2. Ease of use - installation of the appropriate attachments is very quick and easy, after which the tool is ready for use.
  3. Autonomy of operation - any type of power tools are good at home, but in the field they are useless if there is no source of electricity. A chainsaw with appropriate attachments can be used in the field to perform certain tasks.

To expand the functionality of a chainsaw, you don’t need to invent anything. Ready-made attachments for chainsaws are produced by different manufacturers, and to use them, you just need to choose the appropriate option and install it on the tool. To do this, you should first become familiar with the types of devices produced, as well as the features of their correct use.

Important! When installing attachments, do not drain the oil from the chain lubrication tank. This method of avoiding unnecessary consumption of lubricant will lead to rapid wear of the oil pump, which is not designed to operate at idle speed. Contrary to all recommendations, do not allow the oil pump to run idle.

Angle grinder attachment for chainsaw for cutting metal

In the field, there is often a need to cut metal. Purchasing battery-powered angle grinder models is not advisable for a number of reasons:

  • high cost of cordless angle grinders. Their price is sometimes higher than their electric counterparts;
  • low power, so the units are not designed for cutting thick metal;
  • short supply of electricity. Depending on the battery capacity, the tool lasts only 20-40 minutes.

Another thing is attaching an angle grinder to a chainsaw. If the farm has a tool, then you just need to buy the appropriate device for it and get a ready-made unit for cutting metal, which can be used both at home and in the field.

The nozzle is a structure that is attached instead of a tire. It is equipped with a spindle for installing abrasive wheels. It is driven by a belt drive that connects the drive shaft of the chainsaw with the driven shaft of the spindle. The belt drive is driven either by a special pulley, which is installed instead of the standard clutch, or by a standard sprocket.

The devices are designed to work with standard abrasive wheels with a diameter of 160 mm. The internal fixation hole measures 22.2 mm. These attachments are called USHM-1 for chainsaws, and their cost is about $50.

You can see what the tool looks like in operation in the video below.

Important! The maximum rotation speed of the chainsaw shaft is about 12,000 rpm, and the abrasive discs are designed to operate up to 9,000 rpm. To eliminate the possibility of destruction of consumables during operation, you should not operate at full power. It is imperative to follow safety precautions and carry out work wearing a protective helmet.

The attachments can be used not only for cutting metal, but also for sawing wood (using a disk with teeth) or concrete (diamond wheels). In any case, such attachments justify the cost of their purchase by the ability to perform work in the field or on construction sites.

Advantages and disadvantages

An angle grinder attachment can be made from a variety of hand-held gasoline and electric tools. But the simplest and most convenient method is using a chain saw.

Advantages of the device:

  • they are autonomous, that is, a gasoline device will not depend on electrical power, like electric angle grinders, which, on the contrary, need electrical sockets and extension cords;
  • the nozzle can have very high power;
  • it is easy to design and assemble, the main thing is to have the necessary drawings and tools, which can be purchased inexpensively at a hardware store;
  • the price of homemade equipment will be cheaper than the cost of the original.

The disadvantages of homemade nozzles include the following:

  • they are too sensitive to metal dust: chainsaw filters begin to become clogged and fail, and the engine may deteriorate: first it stalls, and then it will not be able to maintain speed and will wear out;
  • grinding discs can constantly break and fly around, and this is very dangerous for the worker himself and the people around him.

To make your device more secure, you need to follow some rules:

  • limit the engine speed of a gasoline saw;
  • you need to use disks that are designed for increased rotation speed;
  • work must be carried out only using a protected casing;
  • the design must have an inertial brake;
  • You need to use models that have a kickback protection function.

The angle grinder attachment has:

  • a pulley that can wear out or break, so you need to monitor the device and, if necessary, change the pulleys on it;
  • In order for the nozzle to work, it must have an adaptive key, consisting of a metal plate, having a hole and 2 steel pins;
  • a special V-belt can transmit torque from the engine to the cutting wheel (the belt is a consumable material);
  • For attachments such as angle grinder 1 and NK - 100, spare bearings are needed, because the bearings themselves are a consumable item.

Chainsaw pump for pumping or pumping water

Chainsaws come with attachments called pumps or pumps. The advantage of such devices is due to the fact that it is possible to obtain a complete unit for pumping out liquid with minimal investment. The cost is about $40 (depending on modification).

Water pump attachments are devices that are installed either instead of the standard chainsaw sprocket, or mounted on brackets for fixing the tire, and are driven by a belt drive. After this, it is also necessary to secure a special cable to adjust and maintain constant speed. The products are equipped with inlet and outlet pipes, to which hoses for pumping water are attached.

The performance of the units depends on the size of the impeller. Such devices can be used to pump both clean water for irrigation and contaminated liquids, for example, from basements, rivers or other bodies of water.

Interesting! Water pump attachments for chainsaws come in different designs, and their housing can be made of plastic or steel. Plastic structures have a reduced cost, but they are not intended for frequent use.

The performance of the offered water pump models is 4800 l/hour. Most attachments are designed to fit 1.5 kW (2 HP) chainsaws. The maximum rotation speed of the turbines of such devices is 6000 rpm.

Chainsaw winch for lifting and moving loads

Manufacturers offer this type of attachment for chainsaws, such as a winch. Used for lifting and moving heavy loads. An important condition when using such devices is their secure fixation. The nozzle is fixed to the ground using metal pins, which are often included in the package. They are often used in agriculture in conjunction with hand plows and hillers.

Nozzles are structures on a separate frame, which consist of a reel with a metal cable (usually 30 meters), and mounted on a shaft. The shaft is attached to the standard Stihl chainsaw sprocket (used for models MS 180, MS210, MS211, MS230 and MS250). Can also be used on instruments from other manufacturers by first installing the appropriate star.


The side where the winch is connected to the tool

The main technical parameter of the devices is traction force (nominal 400 kgf, maximum 600 kgf). One of the options for using a winch for a chainsaw is shown in the video below.

Interesting! The weight of objects lifted using a winch can be up to 500 kg.

Debarker, corroder cup cutter for chainsaw: attachments for wood processing

Special types of chainsaw attachments for removing bark from sawn logs and making longitudinal and transverse grooves are called corroders or debarkers. The products come in two versions: disc and drum. Each option has a corresponding purpose, but the common name debarker is used to designate them.

Drum debarkers are used to remove bark from logs and boards, and disk debarkers, due to the specific design, are designed directly for cutting mounting grooves, bowls and recesses. Let's take a closer look at the models individually.

Disc type nozzles

They are a round cutter with recesses in which the blades are located. Such devices are also called cup cutters. The disc is secured to the spindle using a locknut. The mechanism is driven by a belt drive.

Such devices can be used not only for making grooves in wood, but also for removing bark. However, implementing the latter function will require a lot of time and effort, so it is better to use a coder, the description of which is presented below. A bowl-shaped debarker or figured cutter is used for artistic cutting and making wooden sculptures.

You can see what such a tool looks like in operation in the video below.

The average cost of such attachments is $40-50. However, there are more expensive models that are characterized by highly wear-resistant materials.

Debarkers for drum-type chainsaws

(they are also called coroders and carcinators) are cylindrical elements with several grooves in which blades are installed. The number of knives depends on the modification of the nozzle. There can be 2 or 4 of them. The main purpose of such devices is to remove bark from logs.

Like disk-type nozzles, drum devices are also driven by a belt drive. The principle of installing the corroder attachment on a chainsaw, as well as the features of its use, can be seen in the video.

Main parameters of chainsaw cutters:

  • weight. Their average weight is about 3 kg;
  • minimum power of the chainsaw engine. It is not recommended to use devices on chainsaws with motors whose power is below 3 hp;
  • speed of work. The optimal speed is 8000 rpm;
  • working width. Is 12 cm.

Installation of the nozzle is quite easy. To do this, you need to remove the bar and chain, and also replace the standard sprocket with a pulley. Product prices start at $30.

Let's cut everything around or grinder on a chainsaw

The cutting disc is used in a large size, this is taken taking into account the maximum speed that the chainsaw can produce.

List of materials:

- plywood; - wood screws; — bolts with nuts; - thin sheet metal; - Sheet steel; - a piece of leather or thick rope; — square steel pipe; - cutting wheel.

List of tools:

- rivet gun; — drill and drilling machine; - jigsaw; - lathe; - wrenches, pliers, clutch release wrench, spark plug wrench; — belt grinder; - Bulgarian; — semi-automatic welding machine or inverter; - wood glue; - pencil, ruler, tape measure, paper.

Homemade manufacturing process:

Step one. Preparing the grinder

First of all, remove the tire from the angle grinder, then you will need to remove the clutch along with the sprocket. This task can be quite difficult, since often the clutch is tightly stuck to the shaft and cannot be unscrewed without a service center. To try to unscrew the clutch, you will need a special wrench, it is similar to the one used to unscrew the nut on an angle grinder. Remove the top cover from the angle grinder and remove the spark plug.

Stick as much rope or a piece of leather into the candle hole as you can pull out. This will allow you to block the piston and try to unscrew the clutch. If it works, great!

Step two.
Thrust sleeve Step three.
Making the drive pulley Step four.
Cut out the fastener Step five.
Making a driven pulley Step six. How is the cutting disc attached?

Step seven.
Bearing platform Step eight.
Protective casing Delivery of new homemade products by mail Receive a selection of new homemade products by mail. No spam, only useful ideas!

*By filling out the form you agree to the processing of personal data

Become the author of the site, publish your own articles, descriptions of homemade products and pay for the text. Read more here.

Wood splitter for splitting firewood using a chainsaw

For chainsaws, a special attachment is offered that allows you to turn the sawing tool into a device for quickly and efficiently chopping wood. This is very important in everyday life, when large stumps remain after sawing thick wood. It is almost impossible to cut them with an ax. You can use a hand cleaver, but this process will take a long time and will require a significant investment of time and physical effort.

The average cost of such attachments is about $100. The design is used to work with hemp, the thickness of which can reach 40 cm, and the length varies from 40 to 80 cm. You can see what the tool is in action in the video clip.

The device is designed specifically for Stihl chainsaws of the following models:

  • MS 180;
  • MS 181;
  • MS 210;
  • MS 211;
  • MS 230;
  • MS 250.

It can also be used for chainsaws from other manufacturers, but their minimum power should be 2 horsepower or 1.5 kW. It is important to use tools with an external sprocket.

It is very easy to use the attachment, as well as to mount it on the chainsaw. To do this, you just need to remove the bar and chain and secure the attachment.

Interesting! The wood splitter has a spiral shape that effectively bites into any type of wood, splitting it into pieces.

How to convert a chainsaw into an angle grinder?

Before you make a grinder from a chainsaw, you need to prepare the components required for the job.

To assemble a homemade product, the manufacturer will need:

engine from a chainsaw - it is important that the internal combustion engine has a reserve of power, which will be sufficient for sawing hard metal products. It is best to use a motor with a power of more than 4 liters

With.; working mechanism - a unit from any old household grinder will do. It must be fully operational, otherwise it will not withstand the load from the engine; 4 guide rails, length from 40 to 50 cm; belt; 2 reels.

The work algorithm looks like this:

  1. First, the belt used must be installed parallel to the standard chainsaw bar;
  2. After this, you will need to install a pulley on the utility saw. You can attach the element to the standard drive sprocket of a garden tool;
  3. Then, from the working mechanism of the old grinder, you need to remove the gear built into it and carefully grind it;
  4. After this you will need to assemble the pulley. It must be attached to the general structure of a homemade grinder by welding;
  5. The 2 guide bars remaining from the manufacturer must be shortened. As a result, they should fit tightly into the seats and not interfere with the operation of the belt while it is moving. It is best to sharpen one of the used tires for installing the working mechanism from an old grinder;
  6. Next, all remaining parts of the structure will need to be welded together. After this, the manufacturer will only have to buy cutting wheels and start using the grinder.

When using homemade products, you need to constantly monitor the condition of the air filter from the chainsaw. It must be kept clean, otherwise the homemade device will quickly fail.

Options for outboard motor attachments on a chainsaw

The chainsaw engine can be used as a drive for a boat. To do this, you just need to buy a special ready-made attachment, which is called a “boat motor for a chainsaw.” The nozzle is a device that is equipped with a drive screw. There are different configurations of such nozzles, which have minor design differences.

Their differences lie in such parameters as the number of blades on the propeller, the power of the chainsaw that is suitable for use, the diameter of the propeller, the maximum speed, and the ability to move in reverse. The product is equipped with a special bracket, through which it is attached to the boat.

The attachments are easy to connect to the chainsaw. To do this, you just need to dismantle the bar with the chain, and then secure the device. In order to reduce the speed of rotation of the drive screw, such systems provide a built-in reduction gearbox with a gear ratio of 2:1. The average speed of a boat with these types of attachments is up to 20 km/h, and fuel consumption is about 1 liter per hour. The design provides the ability to change direction, which is achieved thanks to the movable connection of the bracket with the nozzle body. The rotation angle does not exceed 180 degrees.

These attachments are suitable for installation on Stihl chainsaws (MS180, MS181, MS210, MS211, MS230, MS250), as well as models from Carver, Forza, Partner and Husqvarna.

The type of outboard chainsaw motor shown in the photo above costs between $80 and $100. However, there are also more advanced models, for example, from the Bristol company.

The peculiarity of this attachment is that it almost completely replaces a boat motor. It has a function not only for changing direction, but also for reversing. In addition, the change in direction occurs using the handle, and the increase/decrease in speed is adjusted from a hand-held device located on the handle. The disadvantage of such a nozzle is its high cost, as well as its lack of free sale in Russia, Ukraine and Belarus.

How to put an attachment on a chainsaw under a grinder

The nozzle allows you to save money. Manufacturers produce many different models of garden tools. In order not to purchase each type separately, you can choose a special attachment. It helps equipment become multifunctional without spending large sums. The main thing is to install it correctly on the device.

Installation Features

It is recommended to study the rules before installation. Among them:

  1. First of all, you need to make sure that the chainsaw is clean.
  2. Then, remove the side cover, chain and bar.
  3. The equipment is purged using compressed air.
  4. The candle is unscrewed. For this, a rope with knots is used. Afterwards the piston stroke stops. Then the clutch is unscrewed, and then there is calm.
  5. The assembly of the device is carried out in the reverse order. When replacing the side cover, it is recommended to tighten it tightly with several screws.

The hole in the nozzle and the screw rod for adjustment must match. Otherwise, you won't be able to tighten the belt.

Why a chainsaw is suitable for remodeling

The tool has a number of advantages. Among them:

  1. The device is equipped with a motor with a good level of power and performance.
  2. The motor is quite compact.
  3. The engine is ready for use immediately, there is no need for modification.
  4. Suitable for use in any conditions, even at an increased level of complexity.
  5. The convenient design allows you to use the equipment in various positions.
  6. The special arrangement of the clutch helps protect key elements from damage.
  7. The presence of an output shaft allows the use of various attachments and additional devices to expand functions.

When choosing a tool, it is recommended to focus on the following parameters:

  • power value;
  • simplicity and convenience of design;
  • economical price of spare parts.

It is not recommended to use expensive models.

DIY grinder attachment

You can build the nozzle yourself. You will need a kit consisting of the following elements:

  • two pulleys;
  • belt;
  • a shaft equipped with a fastening for disks;
  • old tire;
  • protective casing.

To build a nozzle, it is enough to focus on special drawings.

Start by carefully studying the instructions. The chainsaw tank must be free of oil and fuel. Remove the clutch drum and tire from the housing. The pulley is being fitted.

The belt mechanism is connected to a central disk intended for sawing. This will allow you to change the speed of the main shaft. The nozzle is fixed with pins. Those used to secure the unit tire are suitable.

Whether the nozzle will connect to the equipment depends on the groove, so this is the element that needs to be checked for reliability.

There is a quick method that does not involve tires or other extension cords. It is enough to attach a special adapter to the clutch, which allows you to attach the cutting disc.

It is recommended to take into account several nuances:

  1. The strap should not be placed at the top of the tripod cup, which is related to the clutch. This will lead to poor equipment performance. The belt will begin to fail, so the clutch is replaced with a pulley.
  2. The rotation of the chainsaw blade when the engine is turned on indicates that the clutch has failed. It is unsafe to use such a unit; its functionality is reduced.

Safety Features

When working with a chainsaw, you must carefully follow safety rules. Among them:

  1. The engine speed should be limited.
  2. Only use discs that can withstand high rotation speeds.
  3. Any work is carried out using a protective casing.
  4. The unit must be equipped with an inertia brake.
  5. It is recommended to use chainsaws equipped with a special function that protects against kickback.

An attachment that acts like a grinder is a useful element for a chainsaw. It allows you to increase the functionality of the tool, improve the quality of its work, and take advantage of additional equipment capabilities. You can make it and attach it yourself. You just need to strictly follow the installation instructions.

Motorized drill from a chainsaw for making holes in the ground

If you plan to install posts, for which you will need to prepare holes for their installation, then you can use a chainsaw with an additional motor-drill attachment. This design is completely similar to a standard hand drill, only instead of a handle, a bracket is used to fix the chainsaw. The design of the nozzle also provides for the presence of a reduction gearbox, due to which the speed of the working element is reduced. The gear ratio is 1:56. The result is a maximum screw rotation speed of about 150 rpm. The length of the auger is 1 meter.

Using such a device, you can make holes in the ground with a diameter of 20 cm. Moreover, doing this is much easier and faster than using hand tools. The cost of such a device is about $100. The installation process is quite simple. The kit comes with instructions, which eliminates the possibility of incorrect installation of the product.

The attachment is suitable for Stihl MS180-MS250 chainsaws. However, it can also be used for instruments of other brands with the appropriate power parameters. You can see what the tool is like in action in the video below.

Installation Features

It is recommended to study the rules before installation. Among them:

  1. First of all, you need to make sure that the chainsaw is clean.
  2. Then, remove the side cover, chain and bar.
  3. The equipment is purged using compressed air.
  4. The candle is unscrewed. For this, a rope with knots is used. Afterwards the piston stroke stops. Then the clutch is unscrewed, and then there is calm.
  5. The assembly of the device is carried out in the reverse order. When replacing the side cover, it is recommended to tighten it tightly with several screws.

@lizing-spectehniki.ru

The hole in the nozzle and the screw rod for adjustment must match. Otherwise, you won't be able to tighten the belt.

Ice drill from a chainsaw: a simple attachment to expand the functionality of the tool

From a chainsaw you can get such a useful tool as an ice auger. The nozzle differs from the device for drilling soil not only in the increased number of auger turns (their length is 450 mm), but also in the type of gearbox with a reduction of 1:10. This device is designed specifically for drilling ice and hard soil. The diameter of the drilled holes ranges from 100 to 150 mm (the appropriate model is selected).

The cost of such a nozzle is about $100. There are many modifications of devices available for sale, manufactured by different manufacturers.

At the end of the nozzle there are knives that effectively cut the ice, allowing you to make holes very quickly. Features of installing the device on a chainsaw, as well as its operating efficiency, can be seen in the video clip.

How to make an angle grinder from a chainsaw

The combination of an attachment with a saw not only allows you to effectively cut various materials, but also carry out work regardless of the availability of an electrical outlet. After all, an ordinary angle grinder, angle grinder, or grinder, as the tool is simply called, is equipped with an electric motor, and therefore is completely dependent on the power supply source.

Demand creates supply, and grinder attachments for chainsaws of various modifications have appeared on sale. And folk craftsmen mastered this niche of transformation much earlier. The most common tools used for alterations are Druzhba, Shtil, and Ural.


Finished nozzle - grinder

Creating an angle grinder from a chainsaw is one of the first places in the popularity of such transformations. However, before installing it on the saw, you should understand the features of the transformations and possible failures. As a rule, a ready-made device can be purchased without any problems at the appropriate store.

It should be taken into account that the attachment is not a universal device; it is chosen for a specific modification of the saw. Often, manufacturers do not indicate in the instructions which models the nozzle is suitable for or provide an incomplete list. To ensure compatibility, compare the diameter of the saw crankshaft with the diameter of the attachment pulley, after first removing the clutch from the saw.

Chainsaw attachment - drill: attachment options

The advantage of using a chainsaw as a drill lies in two main points:

  1. The ability to drill holes in materials where there is no electricity.
  2. The high power of the tool will easily allow you to drill large-diameter holes in wood, and at the same time not only gain time, but also maintain the integrity of the electric tool.

A factory-made attachment consists of a housing with a gearbox and a chuck for installing the corresponding drills. Naturally, you can use a chainsaw as a drill only for drilling wood and metal, since the tool does not have an impact mode option. This means that it will not be able to drill through concrete, brick and other hard materials.

The tool chuck allows you to work with drills with a diameter of 16 to 25 mm. The cost of such a device for a chainsaw is about $100. However, the result is not only a highly productive, but also a very powerful tool with great torque. What the process of installing the nozzle is, as well as the features of operating the tool, are shown in the video clip below.

It is important to know that drill attachments are so popular and in demand for chainsaws that they are available in different designs.

A nozzle with a perpendicular arrangement of the cartridge has certain advantages. The main advantage is that when drilling, the user can apply the full force of pressing the tool onto the workpiece, thereby increasing the speed of achieving positive results. In addition, it is much easier for the user to control the tool, which increases the accuracy of the resulting holes.

You should choose these nozzle options if you plan to drill large-diameter holes in solid wood.

Homemade options

In order to make an angle grinder with your own hands, you need to stock up on the necessary components. The simplest and most cost-effective option is to purchase a ready-made factory kit. But before purchasing, you need to check whether it fits the saw you have. The set consists of:

  • Drum or drive pulley;
  • Protective cover;
  • Belt equipment;
  • Key or studs;
  • Detailed instructions, which contain all the drawings and diagrams for correct attachment of the nozzle.

How to turn a chainsaw into a compressor: a useful attachment

A chainsaw can be used as a compressor, with which you can pump up the tires on a car, inflate a rubber boat, or even use it to blow out parts, such as a carburetor.

It is not recommended to use the device to ensure the functioning of a spray gun, spray gun and other pneumatic devices. Firstly, because such a tool does not have a receiver (a container for storing air), so it needs to function constantly until the task is completed. This will accelerate the wear of internal elements. Secondly, doing this is not entirely convenient, since it is necessary to maintain constant engine speeds, while using the other hand to perform specific work with a pneumatic tool. The chainsaw compressor in operation is shown in the video below.

Description

Craftsmen have long been famous for their golden hands and brilliant ideas, which could later be brought to life not only by themselves, but by many other craftsmen.
An example of such a modification is a grinder made from a chainsaw. A grinder can be useful in any household, because it periodically requires grinding and cutting. But if you don’t have one, and you have a saw that runs on gasoline, then you can create a homemade grinder that will work no worse than a production one.


DIY chainsaw grinder

Advantages of a homemade grinder:

  1. Independence in operation and from the electrical network.
  2. High performance compared to electric counterparts.
  3. Significant savings compared to purchasing a new device.
  4. Not the complexity of the alteration work being carried out.

Brush cutter attachment on a chainsaw: purpose

We continue to expand the capabilities of a unique tool - a chainsaw. Manufacturers offer a special device that allows you to turn the tool into a hedge trimmer. Thus, you can significantly save on the purchase of specialized tools.

The nozzle is a structure that is attached to the tire. Dividing the entire length of the tire into sections using such an attachment facilitates effective pruning of bushes, as well as their leveling.

The cost of the device is 30-40 dollars. The effectiveness of the device can be assessed using the video clip below.

Circular saw from a chainsaw: features and purpose

A chainsaw attachment similar in design to an angle grinder is called a circular saw. The essence of its application is to cut wood, which ultimately allows you to obtain a board, batten or timber of the required dimensions.

The device is equipped with an adjustment plate, thanks to which the required size of the resulting workpieces is adjusted. The cost of the nozzle is $50. A saw blade with a diameter of 230 mm is purchased separately.

The device is intended for Stihl and Carver chainsaws, as well as other brands of tools on which you will need to first install a drive pulley of the appropriate type.

Video reviews

Below is a video review demonstrating the chainsaw attachment

Alexander Mikhailovich:

Getting two tools in one is a great idea. A friend who is well versed in repairing such equipment helped me implement it. We used all the necessary parts from the angle grinder and got a multifunctional device. It works great, but I realized that it is better to install a small 115 mm disk, the work will be more efficient.

Advantages: not expensive, multifunctional device.

Disadvantages: Must be used with caution as this is a homemade device

Attachment for rip sawing with a chainsaw or timber jig

To obtain finished boards from even logs, it is necessary to cut the wood longitudinally. And a chainsaw will help the household user in this matter. You can buy a special attachment for longitudinal sawing for it. It's called Timberjig, which allows you to make slats, boards and beams from logs.

The device has a simple design, and is additionally fixed to the tool with an installed bar and chain. The main feature of the device is that there is a scale on the body for setting the appropriate dimensions in order to obtain the required board. Suitable for logs with a diameter of no more than 60 cm.

To use the tool, you will need an additional substrate, which you can make yourself or purchase separately.


Longitudinal sawing with a chainsaw using an attachment

A simplified version of the nozzle is shown in the photo below. The size of the resulting boards is set manually using a ruler.

The need to purchase such a device arises only if straight trees are being felled, from which boards can subsequently be obtained for subsequent sale or household use.

Why a chainsaw is suitable for remodeling

The tool has a number of advantages. Among them:

  1. The device is equipped with a motor with a good level of power and performance.
  2. The motor is quite compact.
  3. The engine is ready for use immediately, there is no need for modification.
  4. Suitable for use in any conditions, even at an increased level of complexity.
  5. The convenient design allows you to use the equipment in various positions.
  6. The special arrangement of the clutch helps protect key elements from damage.
  7. The presence of an output shaft allows the use of various attachments and additional devices to expand functions.

When choosing a tool, it is recommended to focus on the following parameters:

  • power value;
  • simplicity and convenience of design;
  • economical price of spare parts.

It is not recommended to use expensive models.

Planer and jointer from a chainsaw and features of its use

A planer or jointer has a similar design to a corroder. This is a nozzle that is designed to plan off an excess layer of wood, which ultimately allows you to obtain even and smooth planes.

The nozzle has a simple design, and its cost starts from $60 (depending on the modification and design). It is equipped with a cylindrical drum (102 mm wide) with two knives, as well as a support frame that allows you to remove a certain layer of wood.

Attachments are available for chainsaws from Stihl (170-250, 260, 361), Carver, Husqvarna (137, 142, 236, 240) and other manufacturers. They fully replace hand planes, increasing labor productivity hundreds of times.

After processing the wood with a plane, its surface does not need to be sanded, which is also an additional advantage.


Chainsaw jointer at work

You can see how such attachments perform in operation in the video below. The video will allow you to decide whether to purchase a plane attachment for your chainsaw.

Having studied the most popular types of chainsaw attachments, you can draw the appropriate conclusions. The functionality of the tool can be expanded, and quite justifiably. After all, most of the attachments offered by manufacturers may be needed by any tool owner sooner or later. And they not only reduce physical stress, but also allow you to increase the speed of manipulations, as well as minimize the cost of purchasing full-fledged tools. Many people resort to making products on their own, but this will require a lot of time, and in addition, the safety of homemade devices will always be in doubt.

Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]