Today, stainless steel rivets are widely used to connect metal sheets together. To install them, a special tool is used, which is simple, convenient and functional. However, in the process of repair and finishing work, it may be necessary to dismantle hardware. Currently, there is no specialized tool for removing fasteners. Therefore, ordinary people have a logical question: how to remove metal rivets and what tools can help with this?
How to remove rivets from metal
› Metal
14.03.2020
A rivet is a disposable fastener designed to fasten 2 or more parts. To install this fastener, a riveter is used. How to remove a rivet will have to be based on the availability of available tools, because there is no universal tool. In addition, the selection of metal construction materials is carried out in accordance with the technical characteristics.
Aluminum, copper, and steel vary in hardness; they are susceptible to diffusion, oxidation rates, and other physical and chemical processes to varying degrees. The only method that can be called almost universal is drilling. This process can be carried out in 3 ways, which in most cases depends on how close the fastening metal is to the elements being fastened.
- The tight fit of the fastening rod to the hole means that it will not be possible to knock it out. In this case, dismantling will have to be carried out by completely destroying the rod. It is necessary to accurately determine the diameter of the drill used to make a hole in the metal structure. The same drill diameter will be required to remove, or rather, drill out the rivet along with the rim. It is better to start work on removing the rivet at low speeds so that the drill does not damage the fastened parts. However, this method is not the most reliable for dismantling a structure that will need to be reassembled.
There is always a risk that the drill bit of a hand tool will move to the side, enlarging the hole. In this case, it will be difficult to re-fasten the parts using the old marks.
- Dismantling of aluminum rivets can be done using the corkscrew principle with a drill of a smaller diameter than the rivet itself, a self-tapping screw, a screwdriver and pliers.
Despite the large list of tools, the operation will require less time. A hole is drilled in the middle of the rivet, a self-tapping screw is screwed in, and the resulting part is removed with pliers. Steel that fits tightly is almost impossible to remove in this way due to the fact that the drill gets very hot. - Steel ones can be removed using a combined method. To begin with, it is drilled out from both sides along the rim so that the ring-clamps are separated from the rivet rod. Then, in accordance with popular wisdom, they knock out the wedge with the wedge. To do this, you will need a screwdriver with a handle that cannot be destroyed with a hammer blow.
It is inserted into the middle of the rod and with gentle blows of a hammer on the end of the handle, force is applied to remove the rod from the hole; this is the only way it can be removed without damaging the metal being fastened. If the rivet was fastening a thick structure, but it comes out hard, then, if the end is large enough to be grasped with pliers, it can be pulled out.A rivet that does not yield easily can be turned, but it is not recommended to pull it out by shaking if the hole is necessary to re-fasten the structure.
How to remove a blind rivet
The pop rivet is somewhat easier to remove. When dismantling it, it is necessary to remove the ring formed during fastening.
If possible, when compressing the material of the structure, insert a metal saw blade, the fastening can be cut off, and the pin can be removed by pulling it out by the rod.
If sawing or cutting is not possible, there is always a chance to remove the fastening using the first method - drilling.
The hidden fastening can only be removed by drilling, and the exhaust heads can be knocked off with a hammer if the strength of the material they fasten is greater than that of the fastening itself. Provided that using this method of dismantling, there is no confidence in 100% safety for your own hands and the appearance of the material, it is better to abandon it.
, please select a piece of text and press Ctrl+Enter.
Three ways to remove a rivet
Many industrial products use rivets as a way to securely and quickly fasten an assembly that will not be disassembled in the future. Thin sheet metals are often joined this way. If you have a need to remove the rivet without damaging the surface of the product, then I will offer three accessible methods to achieve the desired result.
Drilling out a rivet
The simplest and safest way, from a mechanical point of view, is drilling with a drill.
Take a screwdriver or drill. Install a drill of the required diameter. And we drill through the rivet.
This method will not damage the metals being joined if the drill is selected correctly. Although it is quite specific and will not suit you if your rivets have a semi-circular head.
Dimensions
Installing rivets on the body of the M3 tank
Rivets come in both inch and metric series:
- Imperial units
(fractions of inches) with diameters such as 1/8 inch or 5/16 inch. - Système International or SI units
with diameters such as 3 mm, 8 mm.
The main official standards relate more to technical parameters such as tensile strength and surface finish than to physical length and diameter. They are:
| Reduction | Issued by |
| AIA/NASM | Aerospace Industries Association (AIA) Imperial Standard, NASM is an acronym for National Aerospace Standards, MIL-STD. |
| AN/MS | The US military standard used by the US Army, Navy or Air Force is Imperial. |
| ASME/ANSI | American Society of Mechanical Engineers (ASME), 18-digit PIN, Imperial system approved by ANSI and accepted by the US Department of Defense. |
| BS/BSI | British Standards Institution. provides four-digit BS numbers for imperial standards, and also provides similar BS numbers for official English translations for the internal market of the European Union (see below: DIN or SI) |
| SAE | The Society of Automotive Engineers is an international organization that provides (mostly Imperial) specifications for the design and testing of components used in the automotive industry. |
| JIS | The Japanese Industrial Standard (JIS) is a metric system largely based on DIN with some minor modifications to meet the needs of the Japanese market, commonly used in Japanese electronic equipment. |
| DIN | Deutsches Institut für Normung is the German national metric standard used in most European countries as it is very similar to the new International Organization for Standardization (ISO) specifications. DIN fasteners use the DIN style identifier as well as the material and finish or coating (if any). |
| ISO | The International Organization for Standardization (ISO) is a worldwide metric standard. Refined ISO standards for (metric) fasteners are quickly gaining international acceptance over the similar DIN standard on which SI was originally based. |
Imperial
Rivet diameters are usually measured in 1/32-inch increments and their lengths in 1/16-inch increments, expressed as "dash numbers" at the end of the rivet identification number. The designation "dash 3 dash 4" (XXXXXX-3-4) indicates a diameter of 3 ⁄ 32 inches and a length of 4 ⁄ 16 inches (or 1 ⁄ 4 inches). Some rivet lengths are also available in half sizes
, and have a dash number such as -3.5 (7/32 inch) to indicate that they are half size. The letters and numbers in a rivet identification number preceding its numbers indicate the specification to which the rivet was manufactured and the type of head. Many rivets may have a size 32 stamped on the head of the rivet. Other features on the head of the rivet, such as small raised or depressed dimples or small projections, indicate the alloy of the rivet.
For a rivet to be a secure fastener, it should be inserted into a hole that is ideally 4 to 6 thousandths of an inch larger in diameter. This allows the rivet to be inserted easily and completely, and then the installation allows the rivet to expand, filling the gap tightly and increasing strength.
Metric
The diameter and length of rivets are measured in millimeters. Conveniently, the rivet diameter refers to the drill bit needed to drill the hole for the rivet, not the actual diameter of the rivet, which is slightly smaller. This makes it easy to use a simple drill gauge to check rivet and drill compatibility. Typically diameters from 2 to 20 mm and lengths from 5 to 50 mm are used. The design type, material and any finishing are usually expressed in simple language (often English).
How to rivet a rivet with a riveter
17.04.2020
In most types of installation work, the rivet is used as the main installation component.
And this is quite justified since this particular connecting element allows you to create a connection without using a welding machine.
Moreover, their quality is in no way inferior to the latter, and in some cases even surpasses it. This feature is due to the low cost and reliability of the product.
Also, riveted seams do not require additional maintenance, and they are characterized by increased functional properties such as reliability, practicality and efficiency. Using rivets, objects of different densities are connected. This is due to the specific operation of the component itself.
Rivets have a wide group of classifications, due to which you can always choose the most suitable connecting element to solve specific problems.
There are situations when the riveted seam needs to be disassembled. As a rule, to solve this problem, a special tool is used - a riveter. But it is not always at hand. Therefore, in today’s article we will tell you how to remove a rivet without using a specialized installation tool.
How to remove rivets as quickly and easily as possible
It is worth noting that dismantling the connecting component can be done in several ways and using a varied list of construction tools.
Important : Due to the tight fit of the rivet rod to the hole, normal dismantling will not work. Therefore, in order to remove the fastener, you will have to use hand or power tools.
Method 1 – Drill
In addition to the drill, you will need a metal drill. The diameter of the latter must be greater than the diameter of the rod. But have an indicator less than the head of the fastener.
It is worth remembering that the end result is drilling and destruction of the head of the connecting element. It is also necessary to properly adjust the operation of the drill. To do this, the latter must have a speed control system - they must be set to the minimum value. This way, the most efficient and effective work will be ensured.
Using a low-speed drill will not destroy the sheet itself, but will still allow you to quickly and efficiently remove the rivet. To work with extremely small fasteners, it is best to use a hand drill, this way you will get the best feel for the tool.
In some cases, after drilling the head, the hardware itself does not fall out. Therefore, you should use a light hammer and “finish off” the rod.
Method 2 - Using a chisel
Yes, of course, using a drill is the most effective method as the work will be done quite accurately. However, you don’t always have a special riveter or drill at hand. Then the chisel comes into play. You can dismantle using such a tool in the following way:
- insert the cutting part of the tool under the edge of the head of the fastener;
- hit the tool with a hammer. Due to this, the above-mentioned part will cut off the head and the hardware will fall out;
- Remnants of the rivet, if any, can be removed with a punch.
This method has one significant drawback - the visual component. When working with a chisel, you should forget about the integrity of the workpiece’s coating. Also, during impacts, the anti-corrosion coating will peel off. Therefore, such a tool should be used as a last resort. But if you are a professional in your field, then even a chisel will not cause significant damage to a sheet of metal.
Note : If a rivet needs to be removed from a hard material, then even a chisel will do. However, as a rule, rivets are used to join sheets made of soft metals. Therefore, you need to use a hand tool - a chisel - with extreme caution.
Method 3 – Using a special riveting attachment
It is worth noting that such components are becoming more common and widely used in construction. The demand is due to the simple and effective method of use.
In this case, the method of working with a riveting attachment is exactly the same as with a drill. However, the drilling process will be much more accurate and faster. But there is one unpleasant aspect - the lack of versatility. The fact is that the nozzle is not suitable for every type of fastening, so it must be selected individually for each type of rivet.
How to remove blind rivets
The peculiarity of these types of fasteners is their ease of use. The same applies to dismantling - they are easier to remove than conventional rivets. First of all, it is necessary to remove the ring that forms when attaching the sheets.
When compressing the material, you need to insert a metal blade and cut off the fastener, and remove the pin itself. However, if this cannot be done, then, as in previous cases, the fastening will have to be drilled out.
You can directly dismantle rivets made of aluminum using a drill or corkscrew. In this case, the component must be smaller in diameter than the rivet. As in other cases, it is necessary to use a screwdriver, drill or pliers.
A wide range of tools does not require too much time for dismantling. The latter is carried out much faster. First you need to drill a hole in the middle of the fastening element, screw in a self-tapping screw and use pliers to pull out the structure.
Dismantling of steel rivets is carried out using a combined method. What to do:
- drill the rivet on the sides so that the clamping rings are detached from the base of the product;
- Using a screwdriver and hammer, knock the rod out of the hole. Due to this, you will remove the fastener without causing damage to the workpiece;
- does a paper clip connect a thick structure? Then you need to pull it out using pliers.
In this case, the element can be rotated, but in no case should it be swung if you will use the hole again.
The most common riveter failures and how to prevent them
The principle of operation of the rivet maker is that when the handles are compressed, the collet device grabs and draws a rod from the rivet tube, then with a head placed at the other end it crushes the tube, creating a cap, tightly riveting the hole.
In order for the riveter to serve for a long time, without breakdowns, you should adhere to the following rules:
the head of the riveter must be pressed against the head before pressing the handles and pulling out the rod; it is more prudent to use rivets made of the same material from which the parts being connected are made; for the riveter to work successfully, it is necessary to correctly determine the thickness of the materials being joined: the length of the rivet must be equal to the sum of the diameter of the rivet and the thickness of the materials being fastened; if the rivet maker is equipped with a nozzle for blind rivets, a mouthpiece and a pin that is unsuitable for the work being performed, this may cause the rivet leg to jam; For proper operation of the tool, it is necessary to install the rivet in the rivet gun, then insert the rivet into the hole at an angle of 90 degrees and rivet
It is very important that during the riveting process the tool is at an angle of exactly 90 degrees, and the rivet is completely inserted into the hole, otherwise the rivet will not be installed evenly, and the connection of materials will not be tight; the leg in the rivet maker may jam; after using the rivet gun for 25 hours or at the end of the working day, the jaws, pusher and rivet spring should be cleaned or even replaced if worn; You should regularly wipe the jaw cartridge, the jaws themselves and the jaw pusher from metal shavings. This will increase the service life of the tool. if you select an inappropriate hose diameter for a pneumatic riveter model, the operation of the tool will be incorrect; when working with a pneumatic riveter, you should clean the container filter from chips weekly using a blow gun; the pin of the pneumatic model should be cleaned of chips and lubricated every 50 installations; The rotating parts of the rivet nut should be lubricated every 1000 installations
Otherwise, friction will increase and the speed of work will decrease; The hydraulic oil should be changed at a service center once a year.
mechanika-urala.ru
How to remove rivets from metal?
- 1 How to remove rivets from metal
- 2 How to remove a rivet: tool, video, photo - Turner
- 3 How to change a rivet lock
- 4 How to remove rivets from metal products yourself
- 5 How to remove a rivet from metal?
- 6 How to remove a rivet - tool, video, photo
- 7 Features and types of metal riveting in plumbing
› Metal
14.03.2020
A rivet is a disposable fastener designed to fasten 2 or more parts. To install this fastener, a riveter is used. How to remove a rivet will have to be based on the availability of available tools, because there is no universal tool. In addition, the selection of metal construction materials is carried out in accordance with the technical characteristics.
Aluminum, copper, and steel vary in hardness; they are susceptible to diffusion, oxidation rates, and other physical and chemical processes to varying degrees. The only method that can be called almost universal is drilling. This process can be carried out in 3 ways, which in most cases depends on how close the fastening metal is to the elements being fastened.
- The tight fit of the fastening rod to the hole means that it will not be possible to knock it out. In this case, dismantling will have to be carried out by completely destroying the rod. It is necessary to accurately determine the diameter of the drill used to make a hole in the metal structure. The same drill diameter will be required to remove, or rather, drill out the rivet along with the rim. It is better to start work on removing the rivet at low speeds so that the drill does not damage the fastened parts. However, this method is not the most reliable for dismantling a structure that will need to be reassembled.
There is always a risk that the drill bit of a hand tool will move to the side, enlarging the hole. In this case, it will be difficult to re-fasten the parts using the old marks.
Despite the large list of tools, the operation will require less time. A hole is drilled in the middle of the rivet, a self-tapping screw is screwed in, and the resulting part is removed with pliers. Steel that fits tightly is almost impossible to remove in this way due to the fact that the drill gets very hot.
To do this, you will need a screwdriver with a handle that cannot be destroyed with a hammer blow.
It is inserted into the middle of the rod and with gentle blows of a hammer on the end of the handle, force is applied to remove the rod from the hole; this is the only way it can be removed without damaging the metal being fastened.
If the rivet was fastening a thick structure, but it comes out hard, then, if the end is large enough to be grasped with pliers, it can be pulled out.
A rivet that does not yield easily can be turned, but it is not recommended to pull it out by shaking if the hole is necessary to re-fasten the structure.
How to remove a rivet: tool, video, photo - Turner
17.12.2019
Accessories for clothing are not only decorative, but also a functional addition to products. One of the interesting processes that requires separate consideration is the installation of buttons on clothes - a procedure that can be performed in a studio or tried with your own hands. A detailed description of the process will help you understand the installation principles.
Tools
Using rivets on clothes, you can significantly transform the appearance of the product. Most often, metal fittings are used on jeans, leather jackets and other items made of thick fabric. To install the blocks, you will need the following tools:
- Press for punching holes. A special device made of steel allows you to instantly punch a hole. Before making a hole, the master marks it. Then he brings the textile to a special area under the tool and presses the press. Under the weight of the press, a hole is formed - it is always smooth and small. Workshops often use a large number of attachments for different button diameters;
- Manual punch. This tool looks like an oblong cylinder of small diameter; it is also equipped with attachments. The punch helps to obtain smooth and beautiful holes;
- Hammer. Without a hammer, the punch will not work. When installing buttons on clothes, the master fixes the punch at the site where the future hole will form and hits it with a hammer several times;
- Chalk or soap. These tools are necessary for marking future holes. Usually soap and chalk are used, since the blocks are placed on jeans. If the fabric is painted in a light color, use a fabric marker.
In addition to the listed devices, you need a mini anvil where the punch will work, an awl for making holes and scissors.
Soap or chalkPressHand punch
Hammer
Installation nuances:
To properly attach rivets to clothing, you need to know the principles of the procedure in different cases. You can install the accessories:
- For the finished product;
- On the part when sewing;
- On jeans.
Below are several technologies for working in different cases.
Ready product
A button is a round metal or plastic object used to fasten clothing. There are several types of devices: copper, aluminum, steel, iron. Depending on the type of material, additional tools are used.
For self-installation, use an installation kit for installing buttons on clothing. It consists of 11 items, each of which is designed to work with different types of fittings of different diameters. The set will help you attach the device to clothes, shoes, bags, wallets, and other handmade items.
The procedure for installing rivets for a finished sample of clothing will be as follows:
- Product preparation;
- Use of special tools;
- Functionality check.
First you need to prepare the product: carefully smooth it with an iron, and also mark the places where the buttons will be located. After this, it is recommended to use a special tool for installing fittings and a hammer. It is better to take a small hammer for convenience.
The tool is installed on both sides where the clothes will be fastened, after which it is struck several times with a hammer. Then the buttons are carefully separated from the device. The product already has 2 fastened button parts.
The last step is to check the operation of the buttons: you need to fasten and unfasten the fittings several times to check the functionality and correct installation.
Part when sewn
Manufacturers often install accessories directly during sewing on parts, for example, when making pockets on denim.
In this case, the block can be installed by sewing or riveting using special pliers.
Before purchasing a sewing button, you should pay attention to its design - it does not have a release mechanism, but is equipped with holes for a needle and thread.
It is not recommended to make a hole for the block with your own hands. The most common mistake is using scissors.
Then the hole turns out to be uneven and will become wider over time, which is why the button can easily fly out of the seat.
Many people are interested in the question of how to strengthen the hole for the button: for this you can use special glue - you need to walk the substance along the edges of the hole and leave it to dry for a while.
Select buttons of the sewn type Do not use scissors Sew on the product
Strengthen the button with glue
Jeans
The most common problem when wearing jeans is that they come unbuttoned. This means that the button is not securely installed. A short instruction will help you correctly solve the problem of how to rivet fittings on clothes.
| Stage | Description |
| Preparation | For beginners, it will be easiest to purchase buttons consisting of 4 parts. You will also need an awl, a splitting punch, which will help the button open. |
| Creating a hole | Using an awl, you need to make a hole in the jeans. |
| Installation | Next, you need to insert the button leg into the hole. |
| Fixation | After this, you need to place the button on the product on the anvil and hit it with a hammer. |
Related Posts via Categories
- Strength class of bolts - how well do hardware resist destruction?
- Anchor bolt with nut - proven fastening option
- Dowel-nail – which fasteners are of the highest quality?
- Anchor bolts - a special type of fastener for complex structures
- Designation of bolts according to GOST - navigating the world of hardware
- Making bolts is a clear technological process
- Needle spring cotter pin – eared fastener for mechanical engineering
- High Strength Bolts - Complete Information on Fasteners
- Blind rivet sizes – what should you think about when calculating?
- The washer is spring - the connections will never unwind spontaneously!
How to remove a rivet from metal products yourself
Many industrial products use rivets as a way to securely and quickly fasten an assembly that will not be disassembled in the future. Thin sheet metals are often joined this way. If you have a need to remove the rivet without damaging the surface of the product, then I will offer three accessible methods to achieve the desired result.
We use a drill
The rivet connecting the sheets of metal can be removed as easily as it was installed. In order to remove the hardware, you will need an electric drill and a metal drill. The diameter of the drill tool should be slightly larger than the diameter of the rivet shank, but smaller than the size of the head.
When starting dismantling, you need to know that the ultimate goal of drilling is to destroy the head that holds the fastener in the metal, and not to completely drill out the rivet.
If the diameter of the product rod is unknown, it is necessary to measure the outer edge and, based on this parameter, find the required size in the hardware manufacturer’s catalog.
When drilling a rivet, the number of revolutions of the drill chuck is set to a minimum - this will allow the work to be completed as efficiently and quickly as possible.
The end of the drill is installed in the recess formed by the sides in the center of the head, and the tool itself is positioned so that its axis is strictly perpendicular to the material connected by the rivet.
You need to start drilling very carefully so that the drill does not slip and cause damage to the material. In some cases, especially when it comes to miniature fasteners, it is recommended to use a hand drill.
When the drill “passes” the head of the blind rivet, the connection will fail. In some cases, when the hardware rod does not fall out after drilling, it is recommended to use a hammer and a punch of a suitable size.
In order to knock out a rod from sheet metal, 1-2 precise blows of medium force are usually sufficient. If the work is done carefully, the metal around the joint will not be damaged.
Once the rod is removed from the hole, you can move on to the next rivet.
Types of buttons
To install a rivet in a denim product, first of all, it is worth determining its type and diameter. Today there are several options for accessories for such clothing. When choosing it, you should take into account the size of the existing loop.
Buttons are different. It all depends on the type of fastening and the stud on which the button stands. The optimal solution for everyday wear is a button with an aluminum shank. This metal is durable and resistant. It is much easier to work with than steel products.
With round cut
A common option is buttons, complemented by a round notch.
All metal with smooth base
Often there are all-metal buttons that have a smooth base.
Smooth metal hollow inside
Another popular option is a smooth rod. It is often left empty.
Using a Chisel
The method described above is good in cases where the work needs to be done as carefully as possible, and you have a drill and a set of drills at hand. But sometimes, if the aesthetic component is not too important or when there are no power tools at hand, you can use another method, for example, knocking down the rivet head with a chisel.
Blind rivets are made from alloys of non-ferrous metals or mild steel, so “cutting off” its head with a chisel is not at all difficult.
To remove the fastener, the cutting edge of the tool is inserted under the edge of the head, and then struck with a hammer until the top of the hardware is removed. The remains of the rivet can be knocked out with a punch of the appropriate size.
It is worth saying that this method is not gentle on the elements being connected and, if the metal around the rivet has been painted, the coating will inevitably be damaged.
What to do if there is no spare button
If you don’t want to look for a new rivet, and don’t have the means to turn to professional craftsmen, it is permissible to use an ordinary button instead of special fittings. It is recommended to ensure that it matches the style of the jeans and matches the diameter of the loop.
To carry out the procedure, you should perform the following steps:
- First of all, it is recommended to remove the old rivet.
- After this, the hole from it should be carefully mended. This should leave no unsightly holes.
- Sew a button next to it. It is best to use fittings on a leg.
Sometimes this type of fastener is fixed much more securely and looks much more attractive compared to standard metal rivets.
See also
Instructions on how to properly change the rubber band on a washing machine
Riveting nozzle
In the last few years, in construction stores you can find such a tool as a riveting attachment. This is a simple and effective rivet remover that comes with an electric drill.
The principle of working with the nozzle is the same as with a conventional drill, but drilling can be done faster and more accurately. The device allows you to accurately position the drill above the center of the head and drill to a depth strictly limited by the setting, sufficient to remove the top part of the hardware.
Unfortunately, this device is not universal and for fastening different sizes you will have to use replaceable accessories of different diameters. Purchasing an attachment only makes sense if there is a large amount of dismantling to be done or if the work is carried out under extreme conditions.
Drills with such equipment can often be seen in the arsenal of roofers working at heights - working with the attachment allows you to remove hardware using one hand.
Rivets in construction and mechanical engineering
There are many types of rivets.
Some have the form of a single part - a bushing, which is inserted into the hole and, using a special riveter, the edges of the bushing are expanded on the other side of the parts being connected and pressed (flatten).
Such rivets are the most common, cheap and reliable. They are used mainly in construction and mechanical engineering. How to rivet construction types of rivets?
How to remove a rivet from a metal structure
A rivet is a disposable fastener designed to fasten 2 or more parts. To install this fastener, a riveter is used. How to remove a rivet will have to be based on the availability of available tools, because there is no universal tool. In addition, the selection of metal construction materials is carried out in accordance with the technical characteristics.
Aluminum, copper, and steel vary in hardness; they are susceptible to diffusion, oxidation rates, and other physical and chemical processes to varying degrees. The only method that can be called almost universal is drilling. This process can be carried out in 3 ways, which in most cases depends on how close the fastening metal is to the elements being fastened.
- The tight fit of the fastening rod to the hole means that it will not be possible to knock it out. In this case, dismantling will have to be carried out by completely destroying the rod. It is necessary to accurately determine the diameter of the drill used to make a hole in the metal structure. The same drill diameter will be required to remove, or rather, drill out the rivet along with the rim. It is better to start work on removing the rivet at low speeds so that the drill does not damage the fastened parts. However, this method is not the most reliable for dismantling a structure that will need to be reassembled.
Are you here
How to change a button on your jeans yourself.
A typical case. A button on a pair of jeans broke on a broken leg. The property of this type of button is to jump off the shaft under increased load. Removing button remnants. Remove with a side cutter in one motion. Then the process of installing the button according to your wishes.
Remove the unnecessary denim button.
A) On a broken leg:
If you disassemble the button from the wrong side of the product, you can damage the fabric, so we bite the button from the front side.
B) On a stable stem: First we bite the stem of the button, then what is left. With this method, the fabric is not damaged at all.
Watch the video
Power supply for a beginner radio amateur
Watch the video
Power supply for a beginner radio amateur
Next post
A quick way to install poles
Comments
Site headings
- Aviation
- Auto and motorcycle
- Army and Navy
- Archeology
- Animals
- Health
- Celebrities
- Games
- Interesting
- Internet and computers
- Story
- Space
- Crime
- Cooking
- Culture and art
- Fashion & Style
- Music
- Science and technology
- News
- Society
- Hunting and fishing
- Policy
- Nature
- Psychology
- Travel and leisure
- Entertainment
- Religion
- Rodnoverie
- Needlework
- Garden
- Homemade products
- Sport
- Construction and design
- Secrets and myths
- Economy
- Humor, jokes
- Sandbox
latest comments
When I play Topigr, I would like us to be completely free of problems, and not bess.
Now there is so much that is inexplicable in the world that mom, don’t worry.
Pindos, admit that you have not been to the moon and we will leave you behind.
Basque is the same banderlog as Rotaru! Basques, why aren’t you going to perform in Crimea and Donbass?
The so-called “truly great star” sponsored the genocide of Donbass! Let him speak.
Another pig returned to his pigsty. Donbass has become cleaner.
I agree 90% with the author’s opinion. Here is the opinion of a.filipovic. I still don’t understand who it is.
This is not a sandstorm. The sea receded with the wind and the wind raised the sand.
Gaining popularity
How to make a good wooden chair with your own hands
How to fix a garland if one color doesn't light up
Manual sewing machine from unnecessary trash
How to make a heated bath in your summer cottage
DIY chaise lounge chair made from planks
The information and entertainment site “Labuda” is daily, operational, relevant, interesting news and useful information from different spheres of life.
Full or partial copying of labuda.blog site materials is permitted only if an active and indexable hyperlink to the publication source is indicated.
legal information
Dear authors, remember that the publications you post must not violate the laws of the Russian Federation and the copyrights of third-party resources.
* Extremist and terrorist organizations banned in the Russian Federation and the Republics of Novorossiya: “Right Sector”, “Ukrainian Insurgent Army” (UPA), “ISIS”, “Jabhat Fatah al-Sham” (formerly “Jabhat al-Nusra”, “Jabhat al-Nusra"), National Bolshevik Party (NBP), Al-Qaeda, UNA-UNSO, Taliban, Majlis of the Crimean Tatar People, Jehovah's Witnesses, Misanthropic Division, Brotherhood "Korchinsky, "Art preparation", "Trident named after. Stepan Bandera", "NSO", "Slavic Union", "Format-18", "Hizb ut-Tahrir".
How to remove rivets from metal?
Many industrial products use rivets as a way to securely and quickly fasten an assembly that will not be disassembled in the future. Thin sheet metals are often joined this way. If you have a need to remove the rivet without damaging the surface of the product, then I will offer three accessible methods to achieve the desired result.
How to rivet a rivet? Learn how to use a specialized tool
Rivets are a fairly common type of permanent fastener. Rivets are used not only in industry or production, but also in everyday life. Today, at any construction market in the tool section you can find a riveter.
This is a specialized tool for installing blind rivets (the most common type).
On the website https://rskcorp.ru/katalog-produktsii/zaklepki it is not difficult to buy rivets in bulk from the manufacturer from the RosKrepezh plant. The batch can literally be of any size.
If you believe that rivets will not provide sufficient reliability of installation, this article will provide facts in favor of the opposite.
Types of accessories
Garment accessories include the following parts:
- Buttons.
- Hooks.
- Loops.
- Lightning.
- Blocks.
- Textile Velcro fasteners.
- Holniten are metal rivets. Most often used in denim clothing to secure stitching.
- Buckles.
- Eyelets. Durable metal or plastic fasteners are mainly used in leather goods.
- Rivets. There are utilitarian rivets - those that are used for clamping, fastening and fastening, and decorative ones. Very often, sewing accessories in clothing combine both roles.
Important! All types of fittings are made from different materials. Often, their quality determines how convenient and comfortable a particular item will be worn. In addition, any accessories are designed to rivet and decorate clothes, even if we are talking about such an ordinary detail as a button.
Cutting with a grinder
This is the fastest and at the same time the most traumatic way to remove rivets. Therefore, if you are not confident in using a tool such as an angle grinder (grinder), I sincerely do not recommend using it.
Using an angle grinder, we cut off the heads from all installed rivets.
And use a screwdriver to knock them out.
That's the whole trick.
This method simply damages the surface of the product and breaks the disk itself, since the cutting occurs at an angle. And one wrong move can ruin everything. Be sure to use protective equipment.
Hand tools
Before you rivet the rivet correctly, you will have to understand the entire range of products offered. Most often, there are two types of riveters on counters: manual and pull-out. Their operating principle is not the same:
- Exhaust. The basis is traction, due to which fixation occurs. To do this, the element ends up in the device; with simple squeezing and squeezing, riveting occurs. The fastener itself has a special ball that is flattened. Without it, fixation will not occur even with manual influence.
- What does a lever mechanism do? The operating principle is simple, which is why this manual unit has a low price. The action process is similar, but the ball is fixed in the tube when the handle starts to move. It is used infrequently (for things that are too thin). The choice is made by the buyer, assessing the complexity of the work and the activity of use.
What is a denim button?
Such a small but extremely necessary attribute appeared along with denim clothing. By the way, things familiar to everyone initially served as uniforms for heavy physical work.
Rough fabric must be fastened with reliable fittings, which means that the button is attached directly to the material, otherwise not a single thread will withstand the load. And the button itself is subject to increased strength requirements, which is why they are made of metal.
How much does it cost to put a button on clothes?
for 1 piece Installation of buttons (for shirts and outerwear) – 100 rubles per 1 piece. Installation of denim buttons = 100 – 150 rub./piece. Installation of buttons on jackets, windbreakers = 50 – 150 rub./piece.
Interesting materials:
Is it possible to fly on holiday to Egypt now? Is it possible to fly to Georgia now? Can herring be put in the freezer? Can cabbage seeds be planted in the ground? Can the Charm be worn around the neck? Can chocolate be diluted with milk? Is it possible to sit on the mattress? Is it possible to travel to Bulgaria? Can we say that free fall is the fall of a free body? Is it possible to go to a psychologist without parents?
Tools
- Button set.
- Spoke.
- Pliers, a hammer or something similar to secure the button itself.
- Soft plastic.
- Scissors.
- Rubber.
Specialized stores sell pliers that are convenient for making clamps; they look like pliers. It is better to make sure that there is a suitable attachment for riveting. Before this, a puncture is made at the fixation site, but a little less than is necessary for the part itself. This is done with a knitting needle or a blade - they are prepared in advance.
The front part fixes the button. Everything is done smoothly so that after fastening there is no shift. A plastic figure is mounted for easy mounting. It is made with two holes (top and bottom). After this, the riveting is carefully placed into the created structure. When using forceps, use maximum force. There should be no fear, otherwise nothing will come of it.
