Do-it-yourself punching fingers for a feather picker

Homemade feather removal installation

You can pluck chickens by hand, but you can mechanize the process.
Designed and manufactured a feather removal installation for a regular customer. It is designed to automate the process of de-feathering broilers, laying hens, roosters, turkeys, geese and other farm birds.

It works on the principle of a centrifuge. The lower disk rotates while the drum is stationary.

The installation consists of a frame, a working drum, an electric motor, a bearing unit, and a belt drive.

Frame: welded, made of metal angle. Working drum: diameter 600 mm, made of food-grade polypropylene. Purchased from a store. Disc: made of food grade stainless steel. The installation uses commercially available pen removal pins designed for household pen removal machines.

The advantages of this installation: low cost, ease of maintenance and repair.

Technical characteristics of the installation. Dimensions: length - 1000, width - 700, height - 1200 mm. Number of punching fingers: 110 pcs. Motor: single-phase 220V, 1.5 kW, 1500 rpm. Attaching photo.

The quality of processing is perfect. Carcass processing time is 20 seconds.

It is known: on the farm, it is preferable to buy equipment that has a variety of functions. For example: if you buy a loader, then it must perform various operations in agriculture: load semi-liquid, solid manure; grain, etc. Including, used as a tap. There is a unique tool - a drill-mixer, with which you can drill, prepare a concrete mixture, prepare holes for posts, mix paint, etc. I adapted this drill for no-moldboard tillage - installed it on a homemade electric cultivator, with which you can , without ruining the soil, loosen the soil using the “papillonage” method. By installing a professional drill-mixer with an adjustable speed on a homemade feather removal unit, you can improve the quality of processing poultry carcasses.

Questions:

Equally suitable for birds of all sizes? (From quails to turkeys?) Or should the drum sizes be different for each type of bird? What is the lifespan of these rubber fingers? Wouldn't it be better to make the structure lower, since the height of 1200 mm is not very convenient for work? With such dimensions, how can you clean the installation after work?

Answers:

Regarding the size of the container for different birds. It’s clear: each bird must have its own container size and “its own” fingers. Regarding the resource. I don’t know - I was not involved in the operation of these installations. It’s clear: if you purchase “branded” fingers, the resource will be greater. When purchasing, use paper. If you draw a finger to install it and a mark remains on the paper, then it is better to refuse the purchase. Regarding the height of the structure. The height of the structure can be made significantly smaller. The plastic container has a specific shape. If you cut off the bottom of the container and install a stainless steel tray underneath, the height will be reduced by 150 millimeters. You can cut off the top by 100 mm. You can reduce the distance from the shaft to the zero mark by about 100 - 150 mm. But, the installation was made according to the customer’s requirements at exactly this height. Regarding cleaning. The unit must be cleaned after use with hot water from a hose.

Choosing fingertips

Hello dear farmers! In this article we will look at how to choose the right type and calculate the number of strikers for making your own feather picker or drill attachment.

First, let's look at what beat fingers are (or simply beats, pen fingers).

A hammer pin is a rubber part shaped like a regular pin, with a seating groove from 10 to 25 mm and a length from 50 to 300 mm, depending on the purpose and installation location. The beaters remove the feather due to the frictional force generated when there is contact between the rubber and the bird carcass. They have different shapes of the working surface depending on the type of feather being removed and the type of bird.

The main characteristics of feather fingers are: shape, length, bore diameter, tensile strength, Shore rubber hardness, elasticity and color.

The shapes of the beats are:

To choose the right type of plucking fingers in shape and size, you must know what kind of bird you will be plucking: quail, broilers, chickens, ducks, geese or turkeys.

For quail you need a small finger up to 50mm long and a landing diameter of 10mm. The quail is a small bird, so it is necessary to exclude the possibility of the bird getting stuck between the fingers. If you use fingers 90-100 mm long, the carcasses will fall between the fingers, or these beaters must be installed very often with a minimum distance between them. And this significantly increases the number and, accordingly, the price of purchasing fingers.

Boilers, chickens and turkeys have mostly small feathers, for the removal of which ball-shaped fingers (or spheres) with a length of 90-100mm and a fit with a diameter of 20mm have proven themselves.

Waterfowl ducks, ducks and geese have large feathers, for which ring-shaped fingers (or a ring) with deep ribs, 90-100 mm long and a landing with a diameter of 20 mm work well for plucking. The distance between the ribs of the beel corresponds to the thickness of the pad of the lower part of the feather, which holds the feathers in the skin of the bird.

In order to pluck different birds on one machine, we recommend combining the beating fingers with spheres and ring fingers in equal proportions.

For household centrifuge-type feather removal machines, soft fingers with a value of (48-55 Shore units) are used. In this type of equipment, the bird hits the finger under its own weight; if it is hard, the likelihood of skin tearing increases significantly. For beating drums and feather pick-up attachments, it is also better to use soft fingers, because... It is very difficult to accurately calculate the hand strength with which you need to press the bird to your fingers.

For industrial conveyor lines, stiffer pins with a value of (60-70 Shore units) are used.

The elasticity of rubber is the ability of rubber to quickly return to its original state. In our case, this is the ability to quickly return the finger to its original state when bent.

White rubber fingers have the greatest elasticity. We recommend using it for plucking young poultry. Another property of white rubber is its pleasant smell.

In order to correctly calculate the required number of pins, you need to know what type of equipment they will be installed in. Simply put, decide what you will make: a poultry plucking attachment, a beating drum or a feather picker?

Feather fingers can be made of rubber of varying tensile strength. This value can be from 10-25 mPa. The higher, the more expensive the original rubber and, accordingly, the longer the service life of the finger. For this parameter, select fingers based on the number of poultry heads slaughtered per year. If you slaughter up to 500 pieces/year, take any finger. For large numbers of heads, it is better to take fingers with high strength. This value does not affect the quality of pen removal.

The technological process of removing feathers from a bird also depends on several factors:

• Rotation speed of the feather removal machine or drill attachment;
• Temperature and time for scalding poultry before plucking;
• Choosing the right type of striker fingers.

We hope that this information will help you quickly and efficiently make your own feather picker, poultry plucking attachment or beater drum.

Households very often breed poultry for meat (ducks, geese, broiler chickens, etc.). At the same time, the plucking process is not easy and not very pleasant. It is precisely in order to save owners from such an unpleasant task that a feather removal machine was invented. For use at home, you can make a feather removal machine with your own hands.

Features of feather removal machines for plucking broiler chickens, turkeys, ducks and geese

The material used to make the unit’s body is food-grade stainless steel, and light-colored polypropylene is used to make the drums. This requirement is a recommendation from sanitary inspection and is due to the fact that light-colored materials are easier to control for contamination. In addition, polypropylene has antibacterial properties and is able to inhibit the growth and development of various types of bacteria - salmonella, E. coli, staphylococci and pneumobacilli. The material also has high mechanical strength and can withstand shock loads well. The inner surface of the drum is absolutely smooth, easy to clean and not prone to absorbing dirt.

The device is controlled via a remote control with a power indicator , a switch and an emergency switch located on it. In addition, most units are equipped with a manual irrigation system to improve the plucking process, as well as rollers for transporting the machine and vibration dampers. The units are equipped with single-phase electric motors with a power of 0.7-2.5 kW and can be powered from a 220 or 380 V network. The weight of the pluckers varies from 50 to 120 kg, and the drum rotation speed is about 1500 rpm.

How the devices work

Before you start making your own device, you need to understand the principle of its operation. A pinching machine is a container with rubber pins. These fingers have a special surface that can grab feathers and pull them out. Thus, without any effort, you can get several processed carcasses in a matter of minutes.

Such devices are available in several modifications:

1. With a centrifuge. Round or vertical triangular containers with punching fingers inside. The bottom unwinds at high speed, the carcass also begins to spin and gradually becomes free of feathers. To increase efficiency, a small amount of water is poured into the device - it will protect the carcasses from damage and wash away all excess. Small birds (quails, chickens, ducks) are loaded into it. It is not profitable to use them at home, so other types are suitable for households.
2. With a drum. Here the motor drives the drum. The fingers are located only on the outside. The person must hold the bird close to the rotating rotor, constantly adjusting the pressure. You can clean carcasses of different sizes, but the smallest ones are inconvenient to process.
3. Special attachments for power tools. They are distinguished by their versatility (you can pluck any bird), but they are not very convenient to work with: you have to hold the carcass with one hand and carry out processing with the other. The only justification is that such attachments are inexpensive.

Of course, mechanization of the process has many advantages, but there is also a significant disadvantage - high cost. , only farmers or individual business owners who regularly sell livestock buy such devices

But even when using at home, you want to minimize costs, which is why these days a self-made pen removal machine has gained popularity. There may be several options.

Feather removal machine in the form of an attachment for a screwdriver

This option is one of the simplest. Important advice: you should not try to make fingers yourself, because their cost is low.

In order to make the nozzle, you will need a blank in the shape of a tin can. But the can itself will not work, as the thin tin will bend very quickly. Use thick-walled alloy metal pipe . Attach the bottom on one side using screws, drill a hole in the center, secure the pin in it with nuts (the diameter and dimensions must match the drill chuck). Drill holes for the hammer fingers directly in the cylinder, then insert the rubber bands there - the unit is completely ready for use.

The second economical option: take a sewer pipe made of polyethylene, the diameter of which does not exceed 12 cm. Any hard material is suitable for the bottom. The pin is threaded through, the “cheeks” are tightened using nuts. The fingers are inserted according to the same pattern as described above. To increase productivity and make work easier, the drill can be attached to the table.

A device with a drum works on a similar principle to drill attachments, differing only in its longer length. The drum is located near the supporting axis . For production, a low-power electric motor and a simple pulley gearbox are enough. A large number of birds can be processed, regardless of size. The drum is installed on the frame, a bag for collecting feathers is suspended from below, then you can clean an unlimited number of carcasses.

Homemade mechanisms for plucking poultry

Many people try to save money on purchasing specialized devices by creating them themselves. There are several ways to create a poultry processing unit. In practice, they are in no way inferior to those produced in factories. It is worth considering them in more detail to choose the most preferable one.

Chicken plucker

As a rule, a conventional drill is used as a moving element. One makes approximately the same number of rotations per minute, allowing you to get rid of fluff and feathers from poultry. It is also necessary to make a special drum to which the striking fingers will be attached. It must have a sufficient level of rigidity.

To make the device yourself you need:

• Take a metal pipe with thick walls and weld the bottom to it, making a hole in it.
  It will be used to attach to the drill. Then insert the pin into the hole and secure it with two nuts. It is necessary to select a pin so that it can be sufficiently securely fixed in the electric drill chuck. Pipe for feather removal machine
• Drilling multiple holes at equidistant intervals.
  Drilling holes

• Creation of beating fingers (the more there are, the more effective the process of influencing the carcass will be).
  Creating a nozzle

The pincers for a homemade plucker can be made of different materials. But rubber is best, as it allows you to achieve the desired result without damaging the poultry carcass.

Manufacturing a unit based on a washing machine

To make it, an old washing machine with a fixed cylindrical container, a ready-made drive in the lower part that rotates the bottom, and an installed oil seal is perfect.

The main point of processing is to make maximum use of the standard design. Holes are made in the walls for attaching fingers, and a round plate of hard metal is attached above the bottom (the bottoms of old pots or pans are suitable). The base is attached to the axis. Holes are also drilled in the bottom.

The part that rotates should have dimensions smaller than the tank (about 5 cm). If the gap is too large, bird limbs may get in. It is necessary to equip a water drain at the bottom of the tank, while simultaneously ensuring the tightness of the axle so that water cannot get into the electric motor.

With the help of such a unit you can process both small and large carcasses.

What is a feather removal machine?

Before you decide to make such a device yourself, you need to study this issue and understand the principle of operation of the machine.

The feather removal machine is a container with rubber pins. These fingers have a special surface that grabs feathers and pulls them out. Thus, without much effort you can process several carcasses in a few minutes.

Feather removal machines are available in several versions:

1. With a centrifuge. Such a device looks like a round or triangular vertical container, inside of which the striking fingers are located.

The bottom of this container with the same elements unwinds at high speed. The carcass is rotated and processed with your fingers. This is how she is freed from feathers.

To make the machine more efficient, water is added to the machine. It protects carcasses from damage and washes away excess feathers.

You can load not very large birds into it. For example, you can pluck quails, chickens and ducks. Feather removal machines for geese take up more space and are more energy intensive. Such devices are used mainly in small farms. It is not economically profitable to use them at home. Therefore, for large birds in the household, other feather removal machines are used.

2. With a drum. Here the drum rotates with the help of a motor. The hitting fingers are located outside. The operator holds the carcass against the rotating rotor and adjusts the clamping force.

This machine allows you to pluck birds of any size. Of course, it is inconvenient to pluck small carcasses in this way.

3. Special attachments for power tools. This tool is universal (you can pluck birds of any size), but not very convenient to use. Here you will have to hold the carcass with one hand, and the tool with the other. The inconvenience is justified by the low cost.

Of course, mechanization of the process has many advantages, but there is also one significant drawback - the high price. Therefore, only farms and peasant households that sell livestock regularly buy feather removal machines.

When using at home, you still want to minimize costs as much as possible. It is for this reason that the DIY feather removal machine has become so popular today. Here are several options for such machines.

Application area of ​​the nozzle

Anyone who has tried to pluck a bird's feathers by hand has found that it is quite a troublesome task. If you had to pluck two or three birds in a row, you will agree that this is quite a labor-intensive task. To begin with, the bird must be scalded with boiling water, then plucked by hand to remove fluff, feathers and newly growing feather stumps. After the second or third bird the fingers no longer obey. And if there are more than 10 pieces, this is work for a couple of days, no less. This applies to both hunters and small farms that raise chickens for sale.

Large poultry farms have resolved the issue of feather removal long ago; they use mechanisms for removing feathers on a conveyor belt, which were created relatively long ago. Small farms and hunters use special drill attachments, which are very effective in their work.

Of course, there are also special devices for plucking poultry on sale, but they are practically disposable. Therefore, the invention of such an attachment for a drill, screwdriver or lathe came in handy. Moreover, it is convenient to use it when plucking chicken or quail, as well as musky duck or goose.

Making a screwdriver attachment

The easiest option is to make an attachment for a screwdriver. And just a piece of advice: it is not recommended to make fingers for a pen removal machine with your own hands, since they are so cheap that there is no point in wasting time on them.

To make a screwdriver attachment, you will need a blank in the form of a tin can (the can itself will not work here, since it is made of thin tin, which wrinkles quickly). The workpiece can be made from a thick-walled light-alloy metal pipe. On one side, you need to secure the bottom with screws. A hole is drilled in the center of the bottom, in which a pin is secured with nuts (it should be the size of the drill chuck). Holes for the striking fingers are drilled in the cylinder itself, after which the rubber bands are tucked into the holes - and the device is ready.

Important advantages of the Dak Master nozzle for plucking poultry

• compactness;
• sufficient level of productivity;
• reliability is no worse than that of professional devices;
• Ease of operation;
• no preliminary scalding or scorching of the bird is required;
• maintaining the presentation of the processed carcass;
• The striking fingers are made of a special type of rubber, which ensures the best removal of feathers from the bird;
• The 16 pins of the Duck Master attachment are replaceable and by purchasing an additional set of plucking pins, you can upgrade the attachment after extended use or convert it into a wild bird plucker attachment.

Feather drum

Let's talk about how to make a do-it-yourself feather removal machine with a drum. It works like a drill attachment, only this attachment is longer. The drum is located on the support axis. During production, you can get by with a low-power electric motor and a simple pulley gearbox. This pinching machine can process any number of carcasses, and the size does not matter.

The drum itself is installed on the frame, a bag is hung from below to collect feathers, after which you can clean as many birds as you like.

How to make a feather removal machine with your own hands from a washing machine

For the manufacture of such a device, an old washing machine with a cylindrical stationary container, a ready-made bottom drive for rotating the bottom and an installed oil seal is ideal.

The main idea of ​​the conversion is to make maximum use of the factory design. You need to drill holes in the walls for the pen removal fingers, and install a round plate of hard metal above the bottom. The bottom of an old frying pan or saucepan will also work here. This base needs to be attached to the axle.

You also need to drill holes in the bottom for the hammer fingers.

The rotating part should be smaller in diameter than the tank (approximately 5 cm). There is no need to leave a very large gap to prevent bird limbs from getting in there.

There should be a drain at the bottom of the tank for water with feathers. Important: the rotation axis must be sealed enough to prevent water from getting onto the electric motor.

This feather removal machine is capable of processing both large and small birds.

Barrel skimmer

A feather removal machine, made with your own hands from a barrel, works on the same principle as a device from a washing machine.

Initially, you will need a plastic or metal round barrel (about 1 meter high, about 70 cm wide). This barrel must be strong enough not to bend from blows from the carcass.

At the bottom of the barrel and at the bottom you need to make holes for the rubber strikers. the resulting drum must be placed in the frame. The frame can be made from wooden boards or metal corners. The first option is easier to do, but the second will be more reliable.

To the first layer of the bottom you need to add another one, which will be attached to the rotating mechanism.

In order to mechanize the machine, you will need an electric motor with a power of about 1.5 kW. To protect the motor, it is better to place it on a stand and take it to the side.

In this way, without extra costs, you can make a feather removal machine with your own hands. We discussed above how to do it in different ways.

The big advantage of such a unit is the cost. After all, it is made from scrap materials. A factory feather removal machine is quite expensive.

Feather nozzle design

Feather-removing nozzles for plucking poultry have the form of a drum made of various types of steel (less often plastic). Beating fingers are installed on the outer part of such a drum. The hammer finger is a rubber base that has a ribbed or grooved shape. The different lengths of such fingers indicate what type of birds the device is intended for.

Such a device is called a nozzle because it is only a working body. This organ is driven by a drill or screwdriver. Screwdrivers are rarely used for such purposes, since they have an insufficient number of chuck rotation speeds. The speed of obtaining the final result depends on the number of revolutions.

The length of the beating fingers indicates what species of bird they are intended for. The sizes of rubber fingers for removing feathers from poultry or wild birds are:

• For small birds - 5 cm
• For large carcasses - from 9 cm

The number of fingers on the drum can vary significantly and range from 12 to 24 pieces. The larger the carcass, the longer the beating fingers should be. Thanks to the feather removal attachments on the drill, the plucking procedure becomes easy and quick.

Benefits of use

The most important advantage of poultry plucking attachments is that they do an excellent job with their main purpose - quickly and cleanly freeing the carcass of domestic or wild birds from feathers, fluff and stumps.

If the attachment intended for plucking is of high quality (and this is the quality that distinguishes the products of European, Russian and Ukrainian manufacturers), it can be successfully used to remove down and feathers from bird carcasses of almost any size. Nozzles from domestic manufacturers practically do not differ in quality from products from well-known European companies. This, in particular, is evidenced by numerous positive consumer reviews.

If we focus on the price-quality ratio, then the choice of many will be made in favor of attachments from domestic manufacturers.

The mechanical fingers that are equipped with plucking attachments act on the poultry carcass so gently that they do not cause any harm to the delicate skin located under the feathers and down. A bird carcass completely cleaned using this attachment has a very attractive appearance.

An important advantage of plucking attachments is that they can be used almost anywhere. The main thing here is the ability to connect to an electrical network in order to use a drive device (a conventional drill, screwdriver or sharpening machine).

Worn rubber fingers can be easily replaced, and you can choose a different size if necessary.

It is worth noting several other significant advantages of purchasing attachments for plucking poultry carcasses.

1. The drums of such nozzles are made of stainless steel or other materials that are not subject to oxidation under the influence of high humidity.
2. The average service life of poultry plucking attachments produced by well-known companies is 10 years.
3. The pins with which such attachments are equipped are made of a special rubber compound that is highly wear-resistant. In case of wear of these elements, which occurs due to constant friction against the skin of the poultry carcass, they can be easily replaced with new ones.
4. Many models of poultry plucking attachments come with spare fingers. Even if they are not available, such items are easy to purchase in an online store.
5. It is quite easy to learn how to work with such a device, since the packaging in which the plucking drill attachment goes on sale contains detailed instructions, accompanied by drawings or even photographs.

When choosing between different models of such attachments, you can read reviews from those who already use this useful device. If you have already become the owner of such an attachment, it is better not to limit yourself to studying the rules of its use from text instructions, but to watch a training video on the Internet.

There are no similar posts

Types of plucking attachments

Drill attachments for plucking poultry are divided into two main types. These are nozzles with finger sizes up to 5 cm and from 9 cm. For plucking small poultry, nozzles with finger sizes of 5 cm are used. If you need to remove feathers from bird species such as geese or turkeys, then they will need devices with fingers no smaller than 9 cm

You can use not only attachments for plucking poultry, but also special machines. These machines are barrel-shaped with the punching pins located inside. The device is driven by an electric motor, and the closed walls of the product eliminate the possibility of scattering feathers throughout the workplace.

The production produces pluckers, both stationary and attachments. The cost of stationary ones, called feather removal machines, is much more expensive, so it makes sense to buy them if you have to process several dozen carcasses every day.

Advantages of plucking devices

The main advantage of the products in question is the ability to quickly and easily obtain finished carcasses without feathers. Such devices do not have a negative effect on meat, so they can be used for any type of poultry.

There is no need to specifically buy a drill or screwdriver if you need to remove feathers from poultry. Any rotating mechanism, such as an electric motor, is suitable for such purposes. The disadvantage of using an electric motor is that it cannot be moved. This disadvantage is also an advantage, since during operation the plucked carcass can be held with both hands.

Stationary type of plucker with electric motor

Making a pinching device is not difficult. If such a task is set, then you need to start implementing it by ordering a certain number of nails. It is recommended to order fingers with a reserve so that during operation of the nozzle they can be replaced if necessary.

How to make a poultry plucking attachment with your own hands

Improving such a unique tool as a drill has no limits. Every year its capabilities only expand, thereby making life easier for people. Attachments for drills are sold in specialized tool stores, but it is almost impossible to find feather removal devices there. Such devices can be purchased in agricultural stores or online.

The easiest and cheapest way to use feather removal attachments on a drill for plucking poultry is to make them yourself. The advantage of this solution is ease of manufacture and low investment. You only need to buy one important part - the pins. Their number and length are selected depending on the type of bird. You can buy them separately in any quantity, and their price varies from 15 rubles per piece.

Making feather attachments for drills and screwdrivers with your own hands is done as follows:

1. The nozzle is based on a piece of plastic sewer pipe. The diameter of the pipe does not play a big role, but the optimal value is 60 mm
2. You need to drill holes in the pipe, the diameter of which depends on the size of the fingers (usually 20 mm). You can drill holes in a chaotic sequence or three after two
3. The end parts of the pipe must be covered with wooden circles. After cutting them out according to the pipe template, you need to drill a hole in the center with a diameter of 8 mm.
4. The central hole is necessary in order to place the rod inside. A bolt with a length of 10 cm is used as a rod. Its length depends on the size of the pipe used as a drum
5. Using a bolt with nuts, the wooden bases of the nozzle are secured. First you need to install the fingers on the pipe in the drilled holes.
6. To prevent the plastic pipe from falling off the wooden circles while the drill is running, you need to additionally secure it with self-tapping screws
7. The protruding part of the bolt is the shank, which is fixed in the tool chuck. For convenience, you can remove the threads using an emery machine.

The result is a homemade device that can be used to quickly pluck a chicken or duck at home.

Similarly, you can make from available materials not only an attachment for a drill, but also a stationary machine for plucking poultry. A drum from a washing machine is used as the base, and the device can be driven into rotation by an old medium-power electric motor in the arsenal.

Do-it-yourself punching fingers

Owners of private houses almost always maintain farmsteads and especially love to raise poultry.
But from the moment when tiny yellow balls run around the yard, causing tenderness, to a huge dish with an appetizingly fried chicken, some time passes, filled with the hassle of caring for and raising and, by the way, in this interval there is a period when the bird has to be slaughtered and pluck. This process almost plunges some subtle natures into a deep faint, but, nevertheless, it cannot be avoided.

Plucking with your own hands, even for villagers accustomed to any kind of work, is not only an unpleasant task, but also quite lengthy and tedious.

If you have to process two or three carcasses, then that’s all right, but if you need to slaughter a dozen or two chickens to load into the freezer or take to the market, then the work may take all night.

And if we talk about farms, where hundreds of carcasses have to be processed, then we cannot talk about manual labor at all.

And the industry, of course, took care of automating the plucking process and launched special feather picking machines on the market.

Such devices make it possible to speed up the removal of feathers from a slaughtered bird tens of times, while the quality of work is quite high: the carcass is completely free of feathers and fluff, is not damaged and has an excellent presentation.

We are sure that every private poultry farmer would like to have such a device for plucking birds at home, but its cost is quite high, and not everyone can afford it, and its payback, on a small farm, can take years. We suggest not to be upset about this, but once again to be smart and build such a device yourself.

Let's first take a look at what a feather removal machine actually is.

This device, operating on the principle of a centrifuge, consists of a drum, the entire inner surface of which, as well as the bottom, is studded with rubber beating fingers.

The bottom of the feather removal machine is not rigidly connected to the drum and is a separate moving part.

There is an output tray at the bottom through which the removed pen comes out. The device operates from a single-phase one and a half kilowatt motor.

When plugged into the network, the bottom of the device begins to rotate quickly, constantly turning the carcass over, rubber fingers hook the feather and pull it out, the water pouring from above washes it out through the exit tray. In just a minute, one or two chickens will be cleanly plucked and ready for cutting.

Punching fingers for a homemade pen removal machine

As you can see, the main working elements of the device are the striking fingers.

It is impossible to make them yourself, so our feather removal machine will begin to be built by purchasing them.

The machine may require up to 120 pcs. such elements.

They are also not cheap - for one dollar you are unlikely to be able to buy more than 3-4 rubber fingers, but do not be discouraged ahead of time - in fact, this will be almost the only major investment in this project, everything else can be found in own farm.

When ordering beaters, keep in mind that they come in different sizes and are selected depending on the type of bird. So, when you are planning to pluck broilers, make sure that you do not receive old fingers intended for quail.

Assembling a poultry plucking device

As a container, that is, a drum for a pen-picking machine, you can use a plastic or metal round container, the height of which should be approximately 80-90 cm and the width 70 cm.

The plastic must be very durable, and the metal must be at least 1.2 mm thick. The walls should not bend or crack under the influence of carcass impacts, and the rubber fingers should be secured very firmly.

Since the drum is still separated from the bottom, it can easily be built from the body of an old round washing machine.

Along the bottom of the drum, up to about half or 1/3, and along the bottom, which is a circle with a diameter similar to the container, holes for the beaters are drilled with a wide drill, at a distance of 3-4 cm from each other. The diameter of the holes should be such that the narrow part intended for installation, the fingers fit snugly in the sockets.

Installing the hammer fingers is quite a task, you will break a sweat and spew several megabytes of profanity into the air while getting everything in place. Dipping the elements into some kind of slip-promoting liquid, such as oil or detergent, can make the job somewhat easier.

We make a wooden base for the drum and fix it on it.

The base must be not only strong, but also very stable, since the operation of the feather removal machine is associated with a fairly strong torsional vibration, capable of collapsing the device on its side in no time.

Particular attention should be paid to the arrangement of the bottom. The photo clearly shows that it is two-layer.

The lower circle not only supports the beaters from below, but also consists of a rigid coupling with the transmission device.

The transmission is connected to a motor, which is recommended to be installed slightly to the side.

Since the operation of the feather removal machine will involve the use of water, and the splashing can reach several meters, it is strongly recommended to protect the electric motor with a plastic apron that looks like an inverted basin or something like that.

And after 30 seconds we get an excellent result.

So, in 40 minutes we managed to get rid of the feathers of 17 pieces. broilers

Let's see!

Do-it-yourself feather removal machine: step-by-step instructions

Do-it-yourself feather removal machine - why is it needed? When you come to the store, you buy a ready-made chicken or duck carcass without feathers, but for the time being you don’t think about how they were removed.

And only when you become the owner of your own bird population do you come face to face with the question: how can you quickly but delicately pluck a bird? It is quite possible to make a special device with your own hands, using an unnecessary plastic barrel and spare parts from an old washing machine.

Today we will tell you how to make a feather removal machine with your own hands, list what is needed for this, and offer step-by-step instructions illustrating the entire process.

DIY feather removal machine

Purchased feather removal machines

Despite the fact that bird carcasses are usually sold already plucked, it happens that the bird reaches the table still with feathers - for example, a trophy from a hunt, and it needs to be plucked before cooking. Yes, it’s not a problem to handle one piece, but what if you need to process several dozen carcasses for sale?

For this purpose there is a special device called a feather removal machine. It fully automates the process and eliminates the need for manual plucking.

And the operation takes less than three minutes. This means that even a hundred chickens can be plucked in about 3-4 hours. It is very comfortable.

You can simply buy a functional device, but it is not cheap - from 8 thousand rubles or more.

You can find many models of feather removal machines on sale.

The devices presented in stores operate using an electric motor powered from a regular outlet.

Automatic plucking technology is based on the use of friction: feathers and fluff are removed due to the action of special rotating attachments - beaters.

They are long rubber pins that tear off the feather cover without damaging the skin.

You can find mobile and desktop versions in stores. The first are removable attachments for electric tools (drills or screwdrivers).

They are compact and inexpensive, but not very functional: they allow you to process one carcass over a certain period of time.

But you can take them with you, for example, on a hunt.

Feather nozzle

If chickens or ducks are bred for mass slaughter for meat, then the farm should have a large centrifuge-type machine, in which the beaters are located inside a large central tank.

Such devices have different sizes and, accordingly, make it possible to process a larger or smaller number of carcasses per unit of time.

They also differ in the power of the electric motor and the rotation speed of the drum.

The bird is placed in a tank, the bottom of which rotates, covered with beaters, and additionally the chicken or duck hits the walls with the same attachments. No human action is required.

Small models can be powered by a portable generator

Advantages of homemade pen removal devices

With minimal skills and abilities, it is quite possible to assemble a plucking device that is not inferior in performance to purchased analogues. And you don’t even need a drawing for this, because the assembly is carried out according to a simple and understandable algorithm. Sample instructions can be found below.

If you use spare parts from old household appliances and an unnecessary plastic barrel from construction mixtures or feed, then the cost of the device will be a maximum of a couple of thousand rubles.

You will have to spend most of your money on buying beaters, which you cannot do without. And such a feather removal machine will work no worse than a purchased one.

The only difference is that the appearance is not the most aesthetic, although this defect can be corrected by painting.

An old washer is an excellent basis for a feather removal machine.

Where to buy hitting fingers and which ones to choose

The leading element, mandatory for any feather removal unit, is elastic rubber nozzles.

They are rubber or silicone products that rub against the feathers and thus separate them from the skin.