Lubricant for rotary hammers: top lubricants for drills and gearboxes


Rotary hammer working equipment

The instructions for the mechanism always contain an urgent requirement to lubricate the shank of the replacement tool. The drill absorbs high dynamic loads at the level of thousands of blows per minute.

During continuous operation, the operator should regularly coat the drill shank with lubricant - without this, the attachment will overheat and break. Caring for a rotary hammer is a painstaking task.


Boer

Correct application is carried out in the grooves into which the cartridge wedges fit. It is important to clean them of debris and sand, and then apply a small amount of lubricant to them. When removing a drill or bit, you should always renew the layer of lubricant - a fraction of a gram is enough.

Hammer chuck

Initially, this unit does not have its own protective coating. It is required to add 1-2 grams of lubricant before starting work.


Cartridge

Place of processing – seating surfaces for replaceable tools. This is where colossal friction and shock loads arise that can damage the cartridge. In addition to active protection, this also achieves passive protection: a layer of substance will cover the internal device from the penetration of dust and small particles.

Hammer gearbox

This mechanism is key in an electric tool (after the motor, the rotation of which it transmits to the working attachment). Operating conditions of the gearbox: constantly changing rotation speed and torque, strong friction and increased heating from it. To this should be added penetrating dust and small contaminants - the gearbox is under constant tension.


Hammer gearbox

Lubrication of the rotary hammer gearbox is carried out by applying a substance to the internal surfaces - especially after long-term operation. Bearings and shafts are protected in the same way. It is important to lubricate the rotary hammer gearbox during long-term operation.

Features of oil selection

Before lubricating Bosch rotary hammers, you should select the appropriate oil. When purchasing it, you need to pay attention to the viscosity . High-quality compounds are expensive, but you shouldn't skimp. Such an expensive tool as a rotary hammer requires constant care. What types of lubricant and how much can be used are indicated in the instructions. If such information is not available, specialists from a retail outlet or service center will help you select the best composition. There are universal compounds on sale for processing various models of rotary hammers.

Many people prefer to use graphite lubricants , which have:

  • high quality;
  • good viscosity;
  • affordable price.

If there is no lubricant, you can use lithol or grease . But they cause slight braking of the rotating parts and contribute to increased heating of the tool during operation. It is advisable to buy a special composition in the near future, remove the lithol and apply a new composition.

Before lubricating a rotary hammer drill, you need to make sure that the oil you use is suitable for it. The compounds used for gearboxes are not suitable for lubrication. For the latter, use more liquid products ; they must fill the free cavities and completely cover the parts that are in contact with each other. If there are plastic elements in the gearbox, use silicone grease. It is suitable for processing cartridges.

The transmission mechanism can be lubricated with plastic compounds . But not all tools will work smoothly when using products of this consistency. Thicker mixtures are suitable to reduce tail tip wear. The packaging indicates their purpose for processing drills. If you don’t have them, you can take graphite ones, but they dissipate heat worse.

Manufacturers of electric tools produce their own branded lubricants . They are also produced by enterprises that specialize in the production of lubricant mixtures.

The most popular products include:

  • Bosch - for tail nozzles and gearboxes.
  • Makita – for processing drills.
  • Interskol - for the Boers.
  • Nanotek – for shanks.
  • Turmogrease - universal formulations.
  • Lubcon Thermoplex – for gearboxes.
  • Kress – for lubrication of drills.
  • PRORAB – for processing the seats of tail nozzles.


Lubricant for hammer drills from the Makita brand

Lubricant for drills

High-quality models are sold with the volume of lubricant produced for processing drills. Its intended application is the mating surfaces of the shank. Moreover, the provided viscosity characteristics depend on the brand of the substance.

You should use exactly the brand recommended by the manufacturer. The reason is that the chemical composition is selected to match the construction materials and ensure their integrity during prolonged “hot” work.

It is optimal to purchase consumables of the same brands as the tool.

Briefly about the main thing

To increase the service life of power tools, it is necessary to use only high-quality lubricants. In particular, for uninterrupted operation of the rotary hammer, it is better to opt for specialized compounds that the manufacturer supplies with its products. This will guarantee the correct selection of the necessary lubricant components for this particular model.

You can also use products from leading manufacturers of oils and lubricants. Their universal materials are of high quality and are not much inferior to specialized products. The only condition in this case is the need to change oils more often than usual.

Ratings 0

Read later

Gearbox lubricant

Lubricating the gearbox of a newly purchased hammer drill is not required. The factory has already placed the calculated amount of oil inside, so its presence there is often missed. However, during operation it decomposes, becomes dirty and ceases to fulfill its role.

After some time, it is recommended to replace the oil with one that is designed for harsh operating conditions and high heat. Friction occurs inside the gearbox during rotation, characterized by frequent and sharp squeezing of fluid from the friction pairs. Therefore, specialized oils are used that can:

  • protect metals from oxidation;
  • capture and remove pollution;
  • stick to surfaces to protect them;
  • be water-repellent;
  • do not be afraid of strong heat,
  • as well as self-healing.

Causes of equipment overheating

Many home craftsmen have a question about how to use a hammer drill so that its gear housing does not overheat. First of all, you should find out the reason for the excessive heating. One of these reasons may be too much lubricant in the internal part of the gearbox, which also negatively affects the performance of the device.

The reason for the intense heating of the rotary hammer gearbox may also be that an insufficient amount of lubricant is supplied to its internal parts. This can happen in cases where the hammer drill is used for too long in the chiselling mode.

Through this hole in the hammer drill body, lubricant is periodically added during operation.

Another common reason for the device to overheat is that the holes through which cooling air flows to the hammer drill motor are clogged. In such cases, it is necessary to thoroughly clean the rotary hammer from dust and switch it to normal drilling mode for a while. When operating in this gentle mode for about half an hour, the temperature of the gearbox housing should decrease.

With proper care of the technical condition of the rotary hammer and compliance with all recommendations for its use, the gear housing should not overheat under any operating conditions.

Top 4 lubricants for rotary hammer drills

Lubricant for hammer drills is individually selected for the brand of the tool itself, but there are several universal formulations. They stand out from the crowd, but the application remains up to the decision of the hammer drill operator.

The following are good for construction and domestic conditions, therefore they are used quite widely.

Hammer lubricant: makita 196804 7

Origin: Japan.

Purpose: processing of the shank and the inside of the chuck.

Release form: soft tube, 95 g.

Pros:

  • lack of decomposition and transformation into wax;
  • operational reliability and high level of surface protection;
  • Convenience of storage containers.

Minuses:

  • decent price;
  • the chemical composition is a secret of the manufacturer.

Impression: smooth operation even after long hours of use.

Hammer lubricant: arsenal ar 401 100 g patriot

Origin: USA.

Purpose: processing of any replaceable drills used when rotating up to 4 thousand revolutions per minute.

Release form: flexible tube, 100 g.

Pros:

  • retention of dusty contaminants – at a height;
  • protection power – just right for intensive work with minimal consumption of tube contents;
  • sufficient initial fluidity for fast and reliable processing of complex configurations;
  • practical container that allows you to get a minimum amount of the composition.

Minuses:

  • heated liquid has increased fluidity, which slightly reduces performance characteristics;
  • the tube sometimes produces strong splashes, the price of which is lost composition and contaminated surfaces;
  • There is no usual relief - it is problematic to open without removing gloves or with wet hands.

Impression: a decent lubricant at a not too high price, which lasts for a long time. How to use is intuitive.

Lubricant for rotary hammer: bison zsb 125

Origin: Russian Federation.

Purpose: replaceable tools with difficult working conditions (bit, chisel, drill), for cartridges of any configuration.

Release form: soft tube, 125 g.

Pros:

  • enhanced chemical composition to withstand extreme loads;
  • resistance to moisture and the formation of aqueous emulsion;
  • reliable corrosion protection and high tribological properties;
  • relatively low price;
  • significant operating temperature range: from -50 to +130 degrees.

Minuses:

  • relatively rapid acquisition of a liquid state;
  • possible ejection from the rotating cartridge;
  • does not rub off well from absorbent materials.

Impression: a semi-synthetic substance, packaged in a convenient tube, does its job efficiently, but you need to get used to its slightly lower viscosity.

Hammer lubricant: elitech 2006 000100

Origin: Russian Federation.

Purpose: to counteract friction and corrosion of replaceable tools and chucks.

Release form: tube, 60 g.

Pros:

  • powerful operating temperature range: from -55 to +140 degrees;
  • there is no scattering of individual drops;
  • versatility of use - suitable for any type of tool and any working conditions.

Minuses:

  • Possible strong darkening when working too hard and drying out when stored for too long;
  • relatively small volume.

Impression: reliable material at an affordable price that will not turn into liquid oil.

How to lubricate correctly

To correctly apply the lubricant to the rotating parts of the hammer drill, you need to study the instructions. It indicates what needs to be done and in what order. It also indicates what consistency the lubricant should be.

The following steps are required:

  • prepare lubricant for the hammer drill;
  • remove the rotating elements from the housing and clean them from dust and dirt;
  • let the parts dry;
  • apply the mixture to the rotating elements in sufficient quantity;
  • put everything back together in reverse order.

Important . Excessive lubricant clogs the hammer drill, reducing its service life. Therefore, there is no need to apply more substance than required.

The instructions describe in detail how to perform all the steps yourself. It is worth considering in more detail how to properly lubricate the main elements of a hammer drill.

Before disassembly, you need to prepare the necessary tools. If you have no experience in assembling/disassembling rotary hammers, then you should watch several videos on the Internet. This will reduce the risk of errors and allow you to assemble everything correctly.

Gearbox

It is located inside the product. Not everyone knows that it also needs to be lubricated. If the level of friction is high, the hammer drill overheats. Here's how to process a gearbox yourself:

  1. Cleaning the rotary hammer from dust. To do this, use a damp cloth or rag. The entire housing must be thoroughly wiped to ensure that no solid particles get into the parts. Some components burn out when debris gets into them.
  2. Disassembling the case. It is recommended to remember which elements are located where. Do not process the gearbox immediately after using the hammer drill. Hot elements often break after contact with cold material.
  3. Removing the gearbox from the housing to wash it with gasoline or spindle oil. It is also recommended to rinse the inside of the case as much as possible. Kerosene, gasoline or other substances are used for this.
  4. After drying the part, apply lubricant evenly to its entire surface. It is important to note that during disassembly, not all components of the tool were lubricated. This means that they do not need to be processed.
  5. After completing all the steps, you need to assemble the hammer drill.

Cartridge

This element becomes clogged during operation. If dust and debris are not removed, the cartridge will jam. The manufacturer indicates what substance is required to treat the hammer drill cartridge. Here's how to take preventative care:

  1. First, the cartridge is separated from the tool and disassembled into individual components.
  2. Each part is washed in kerosene or gasoline to remove dust and other solids.
  3. Lubricate all components of the cartridges with the material recommended by the manufacturer.
  4. Reassemble everything and install it back.

Important . The cartridge must be lubricated simultaneously with the gearbox. This will extend the life of the tool.

For the drill, as a rule, the same material is used as for the shank. To reduce friction and improve the performance of the hammer drill, oil/cream is applied each time before work. If the drill is changed, it needs to be processed again.

  1. The required drill is selected. It must be clean, without traces of dirt and dust.
  2. There are special grooves on its base. You need to introduce a lubricant into them.
  3. Place the drill in the chuck and start working.

The grooves are well processed. Usually a creamy mixture is used.

Top 3 lubricants for rotary hammer gearboxes

The most loaded parts of the gearbox are the gear teeth and bearings. For them, substances are manufactured with capabilities designed to resist water and high temperatures.


Hammer gearbox

Lubrication of the rotary hammer gearbox can be done well with one of the three products listed above. How to lubricate the gearbox is up to the operator to decide.

Hammer lubricant: makita p 08361

Origin: Russian Federation.

Purpose: high-power rotary hammers and jackhammers (with SDS-Max chuck).

Release form: tube, 30 g.

Pros:

  • easy to use with viscous consistency;
  • coloring indicates untreated areas;
  • minimum storage space.

Minuses:

  • the manufacturer hides the chemical composition, so it is difficult to replace with an analogue;
  • will leak from models without an oil seal;
  • small volume, which is enough for only a couple of uses;

Impression: reliable composition for models with a shock mechanism and high vibration.

Lubricant for rotary hammer: ultra 50 g vmpavto et 110005

Origin: Russian Federation.

Purpose: removal of contaminants and removal of heat in gearboxes with gear and hypoid transmissions.

Release form: transparent rectangular package, 50 g.

Pros:

  • high wetting of metals;
  • self-distribution in work;
  • the consistency is equally viscous and liquid;
  • low cost.

Minuses:

  • ability to exit from any gap if the loading quantity is exceeded;
  • practicality suffers from a strong odor;
  • packaging may seem inconvenient;
  • the amount of content is enough for a couple of refills.

Impression: the lubricant has high fluidity, which increases its functionality - penetration into far corners and between all teeth is carried out independently.

Hammer lubricant: ultra 200 g vmpavto

Origin: Russian Federation.

Purpose: transmissions with gear and planetary gears used at high speeds.

Release form: tube, 200 gr.

Pros:

  • easy and quick distribution over the surface;
  • additives to improve tribological properties;
  • heat removal at high speeds;
  • A decent volume is sufficient for long-term use.

Minuses:

  • not the best results for rotary hammers with low operating speeds (less than 1500 rpm);
  • relatively high price.

Impression: the dark-colored composition is convenient for the hammer drill gearbox and has high performance properties.

Leading lubricant manufacturers

Before wondering how to lubricate a hammer drill, you need to choose the right product. Having understood the crankcase design and choosing either liquid or grease lubrication, you need to choose the manufacturer. And here you can go one of two ways.

The easiest thing to follow is a brand. Bosch, Makita, Lubcon, AEG are widely popular. In this case, you need to use lubricant from the same manufacturer that manufactured the tool. This ensures that all of the above requirements will be met.

In addition, such lubricants often have accompanying documents, which even indicate specific models that are best compatible with the product. Sometimes there is even a list of other brands whose equipment can use this product. But you still need to be extremely careful in your choice.


Lubricant products from Bosch Source allegroimg.com

You can also use universal lubricants from leading manufacturers. Companies such as Castrol, Xado, Ravenol and Shell produce a line of oils that are equally suitable for any equipment. And the only condition for proper use is that there is an indication on the product packaging that this is indeed a lubricant for the gearbox of a power tool.

The owner can only choose the consistency. And the technical documentation included with the hammer drill will help you do this correctly. There is always complete information there, including recommendations for lubrication of working units.

How else to lubricate the rotary hammer gearbox

How to lubricate in the absence of special equipment? Contrary to recommendations regarding specially developed mixtures, the use of solid oil or lithol is allowed for a short period of time. These proven materials are cheap and widely available, unlike hammer drill lubricant.

They allow for short-term protection of nodes in the absence of other means. The disadvantages of this solution are some braking of the mechanisms and low heat removal. What kind of lubricant is available in the field is a question, so using them is the best solution if you are empty-handed.

Tags

Other lubricants Lubricant for need lubricant for Composition of lubricant for instead of lubricant for Lubricant for Universal lubricants for then lubricant for need lubricant for hammer drill tips The work of a hammer drill is coupled to the hammer drills, the hammer drill is used, the hammer drill stops, the group of the hammer drill can, the hammer drills are not allowed. tool ends lubricate the tool. for drills for drills use for Bosch drills for Makita drills for Interskol drills for drills for rotary hammer drills the drill shank has the extraction of the drill will have to break the drill.

packagingsds

Review of Dnipro-M demolition hammers

Our brand's assortment includes several models of jackhammers that are suitable for performing work of varying complexity.

SH-160

In size, this model is no larger than a hammer drill, but has excellent technical characteristics. Weighing only 5.5 kg, the tool is capable of destroying up to 5 tons of concrete daily. The SH-160 jackhammer can easily handle concrete, brick and stone.

You will find it convenient to work with this model not only due to its compact size and light weight, but also to the presence of AVT technology, which significantly reduces vibration levels. The handle of the tool is rubberized and allows you to hold it securely in any working conditions. The SH-160 also has a tool position adjustment function that allows you to change it in a few seconds.

The number of blows when working with the model reaches 3600 per minute, which ensures the required pace of work. The nozzle is firmly held in the SDS-max chuck even with the most intensive use.

SH-210AV

The SH-210AV is great for breaking down even the toughest materials. It easily copes with the task of dismantling foundations, monolithic structures, and asphalt pavement. The 2100 W motor and 65 J impact force can destroy 7 tons of concrete per day. You can work comfortably throughout the working day thanks to AVT technology, which reduces vibration during operation.

The jackhammer package includes a case made of impact-resistant plastic. The case has wheels that make it easy to move the tool. The package also includes: SDS HEX pick and chisel, additional handle, gearbox and shank oil.

The comfortable handle with an internal width of 134 mm allows you to hold the tool with both hands. The package also includes an additional handle that can be rotated 360 degrees, improving the quality of control of the jackhammer.

SH-220AV

The most powerful jackhammer model in the Dnipro-M range. It has become the choice of professionals who successfully use it to work with foundations, monolithic structures, stone and asphalt. With a power of 2200 W and an impact force of 65 J, you can destroy 10 tons of concrete per day. The service life of the model is increased thanks to the metal gear housing, which improves engine cooling and allows the tool to operate stably for a long time.

What is a jackhammer, how does it work?

The device is a percussion tool designed to break and split rock sediment, concrete structures, asphalt, etc. The hammer is controlled manually by the operator; the direction of impact, frequency and duration of impact on the surface being treated are regulated. Since the force is transmitted to the working element (pike, blade, chisel, etc.) from the striker driven by an external energy source, the device belongs to the mechanized class of tools. The drive may be

The number of beats varies from 15 to 45 Hz. (i.e. 15–45 working movements of the striker per second).

In addition to manual jackhammers, there are machine tools that use a similar operating principle. They are used in the development of rocks in mines and open pits. The inventor of the machines is considered to be the French engineer Germain Sommeye (late 50s of the 19th century).

Mobile jackhammer in a mine tunnel

Bumper device

Despite the variety of types, their principle of operation is no different. The working part is a chisel, a peak or a slotting blade. This is, as a rule, a hexagon made of high-strength steel, pointed at the end. It is activated by a firing pin, which receives an impulse from the drive mechanism. The firing pin and piston are installed in the sleeve. Between them there is an air space, which, compressing, pushes the firing pin towards the peak. This design is necessary so that the destructive force does not have a direct application to the drive mechanism. Otherwise, shocks of 30–50 kJ. would quickly destroy the engine rod. During the reverse stroke of the piston, a reduced air pressure is formed inside the liner, which “pulls” the firing pin into its original position and the cycle repeats again. Regardless of the design solution of the drive, the mechanical part of the bump stop remains unchanged.

Jackhammer with hexagon 28.6mm Makita HM1317CB

After selecting the impact force, you need to carry out preparatory manipulations with the jackhammer. Jackhammers of different power differ in design.

Please note that any decent manufacturer of professional jackhammers makes handles with anti-vibration dampers that protect your joints from injuries and occupational diseases.

If an anti-vibration handle is not included in the design, we recommend not using this technique. Otherwise you will be dealing with cheap production.

Rating
( 2 ratings, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]