Chainsaw Partner P360S - a new generation household model

In the private sector and country cottages, the Partner P360S household chainsaw is used for partial or complete mechanization of household and construction work.

The operational characteristics of the tool determine its suitability for the preparation of wood fuel, the construction of wooden structures, the formation of tree crowns and tall shrubs.

Photo: Partner P360S chainsaw

Rating characteristics

In a relatively short time, the brand assortment produced has achieved high ratings.
Positive reviews from owners and specialists of service and repair structures can serve as confirmation of excellent technical and performance characteristics. The quality, reliability and durability of the component units corresponds to the level of modern standards and current regulatory documentation. The affordable cost of Partner chainsaws did not affect the full equipment.

The standard list contains:

• easy start systems;
• easy-to-access mechanisms for tool-free chain tension adjustment;
• air intakes with combined air purification.

Operational advantages

First of all this:

• optimal combination of cost, operational capabilities and working life;
• quite powerful and economical power unit;
• productive 18-inch headset;
• easy start system;
• inertial emergency stop brake.

Saw Partner P360S in its technical and performance characteristics meets all the requirements of standards and current regulatory documents.

Despite the budget level of cost, the design of the product includes design solutions typical for semi-professional class models.

Carburetor adjustment

Factory settings of fuel equipment are carried out according to standard indicators of air temperature and atmospheric pressure. Additional carburetor adjustment is necessary if the engine does not start or does not develop speed after warming up. In another variant, it stalls when you press the gas or does not work at idle speed.

The most likely cause of this malfunction is the mixture entering the engine cylinder is too rich or too lean. The recommended sequence for setting up the fuel supply system is given in the maintenance and operating instructions.

By rotating the quantity and quality adjusting screws, the gasoline-oil emulsion is brought to the standard proportion of 1:16.

The key to successful setup is:

• high-quality gasoline and properly prepared fuel mixture;
• preliminary cleaning of the air filter;
• warming up the engine to operating temperature level.

If there is a breather in the engine design, you should ensure that it is in good working order. The constant ignition gap does not need adjustment. In order to set the ignition correctly, it is enough to adjust the gap in the spark plug.

All models of the brand range operate on a fuel mixture prepared from gasoline and motor oil intended for engines with two-stroke gas distribution. The oil proportions are standard 40:1, for some models this figure is 50:1.

Depending on the air temperature, consumables are selected from the company list recommended by the instructions. It is allowed to use analogs of the same quality that are identical in characteristics. Motor oils and their chain analogues are not interchangeable.

Model device

The design of the Partner P360S chain saw is a classic solution typical for equipment of a similar type. The model is distinguished by its convenient location of filling necks for working fluids. Units and points for making settings and adjustments are located rationally and conveniently, which greatly facilitates daily care and necessary service.

Service

The Partner chainsaw runs on a fuel mixture of AI-92 gasoline and Partner branded oil in a ratio of 40:1. To lubricate the chain, which is carried out automatically, use the oil specified in the user manual, in accordance with the season of operation. Mandatory maintenance is performed after 10/20 operating hours.

You can learn more about the features of the device, operation, making the necessary settings and adjustments of the Partner P360S chainsaw, and practical recommendations for troubleshooting breakdowns and malfunctions yourself in the factory instructions.

Specifications

The Partner P360S saw has a 40 cm3 engine with a power of 1520 W (2.07 hp). This power is quite enough to ensure that the idle speed is 3300 rpm. To operate the saw, a 450 mm long bar with a 6-tooth drive sprocket is used, as well as a chain with a pitch of 9.53 mm and a drive link thickness of 1.27 mm, which perform high-quality cuts up to 42 cm in length. The maximum braking speed of the Partner P360S is only 0. 12 s.

The volume of the fuel tank of the saw is 250 cm3, and the oil tank is 150 cm3. Fuel consumption is 530.15 g/kWh.

The weight of the tool without chain and bar is 4.8 kg.

Veng. 40 cc, power 1.52 kW (2.2 hp) weight 4.8 kg

Features of application

1. The Partner chainsaw provides a thin, high-quality sawing cut.
2. Structurally, it is possible to quickly install the tire and tension the chain without the use of special equipment.
3. Thanks to the optimal balancing of the design and comfortable grips, the chain saw is extremely ergonomic in operation, which ensures stable performance of the operator.
4. It is not for nothing that the Partner P360S chainsaw is called the latest generation household model - thanks to its high performance characteristics, the tool is suitable for collecting firewood, constructing wooden structures, carrying out sanitary and preventive work in the garden and park.
5. Despite the budget price of the Partner chainsaw, its design uses technological solutions typical for more productive models of the semi-professional category.
6. Cooling of the chain during operation is carried out automatically under pressure.

Owner reviews

The Patriot saw was purchased recently for 6,000 rubles. The tool is durable, reliable and easy to maintain, but its capabilities are very limited. There is not enough power to cut thick wood; at temperatures above +25 degrees Celsius, you have to take long breaks for cooling. I didn’t like the design of the air purifier; I had to modify it by installing a foam filter. Dimon

I went to the city to buy the Shtil I had been eyeing for a long time, but due to an unexpected price increase I had to buy a Partner chainsaw. The store immediately asked me to replace the long tire with a 16-inch analogue and to pick up a good chain. The commissioning of the saw was successful, the machine started on the second try. I liked the performance of the engine right away, the exhaust cut-off is clear and low-noise, and the vibration is moderate. Sawing is efficient, the chain runs smoothly and without jerking. I am satisfied with the purchase in all respects, I recommend it. Fedor Stepanovich

Device

The design of the tool uses a classic layout combined with modern design and ergonomic solutions.

• The saw body contains an air-cooled engine with air purification and exhaust noise absorption systems, tanks with a fuel mixture and oil for chain lubrication. The drive sprocket serves to drive the cutting chain.
• The cutting device consists of a removable guide bar and a chain with a tensioning device, which, in operating mode, moves at high speed along a longitudinal groove 1.5 mm wide.

The chain is cooled by oil, which is supplied in the required quantity by an automatic dispenser depending on the operating mode. Motor oils and chain lubricants have different properties and are therefore not interchangeable. If the chain is not lubricated, is subject to overheating and accelerated wear, then the reason is most likely a failure of the oil dispenser.

Headset

The tire and chain are included in the list of replacement equipment. Depending on the type of work, the tool can be equipped with tires 14-18 inches long. A design feature is the ability to replace and adjust chain tension without using a tool.

To cool the chain, a system of automatic lubricant supply under pressure to the working area is activated. Oil enters the inlet of the built-in pump from an internal reservoir with a volume of 150 ml.

In accordance with safety requirements, the headset is equipped with an emergency stop system and a chain catcher, which virtually eliminates the risk of injury to the operator in the event of unusual situations.

Analogs

The saw is fully competitive with tools of other well-known brands that are identical in cost and performance parameters. Consumer demand for the DAEWOO DACS 4516, PATRIOT PT 5220 Imperial, Hitachi CS 33 EB and Ryobi RCS3835T models is consistently high.

In the domestic market assortment, powerful and reliable saws Zubr PBC-490 45DP, SPEC BP-4518, as well as a number of household models Kalibr, Ural and Zenit are in demand.

It should be noted that in the production of domestic chainsaws foreign components and modern technologies are used, therefore, in terms of operational capabilities, many domestic tools in this category are not inferior to imported analogues.

Malfunctions and repairs

The Partner P360S 18 chainsaw should be serviced at a service center, but if this is not possible, then some faults can be fixed yourself. For example, replace the spark plug if the spark is lost, or the drive sprocket if it is worn out.

Let's look at the main problems with Partner 360.

No spark

In order to check the spark on the spark plug, you need to unscrew it from the cylinder, install it in the cap of the high-voltage wire from the coil and, placing it on the cylinder, pull the starter several times. In this case, the ignition switch must be in the “on” position.

If there is no spark on Partner 360, then the reasons for its absence are the following:

1. The spark plug is faulty. To fix this, you need to replace the spark plug. To do this, you need to remove the top cover, use a universal key to unscrew the old one and install a new one, known to be good, in its place.
2. Broken high-voltage wire. To check, you need to conduct an inspection. If the wire is cracked or completely torn off, it will need to be replaced. Partner chainsaws use ignition coils with a permanently fastened armored wire, so if it breaks, you will have to change the coil.
3. The ignition coil is faulty. Diagnosing a faulty coil on your own is quite difficult, because... This will require special equipment. It is much easier to install a known working coil on the saw and try to start it. If the saw does not start, then the problem is not in the coil, and you need to continue troubleshooting.
4. Melting and short circuit of the wires going to the ignition switch. It is not uncommon for the wires from the ignition coil to the switch to melt in the cylinder area. Their closure results in the absence of a spark at the spark plug contacts.

If you have checked all the points and have not found the reason for the lack of spark, then you need to contact a service center.

Fuel supply cut

Occasionally, for a variety of reasons, the fuel supply to the Partner P360S may be interrupted. The malfunction can be determined as follows: after several unsuccessful starting attempts, unscrew the spark plug and check its condition. Dry means there is no fuel supply to the cylinder and diagnostics need to be carried out.

A wet spark plug indicates there is no spark or too much fuel is being supplied. The reasons for the lack of fuel supply are as follows:

1. The fuel filter is dirty and does not allow gasoline to pass through; to eliminate this, replace the filter.
2. The fuel line is clogged; to check, you need to disconnect the fuel hose from the filter and carburetor, using a piece of hose of suitable diameter and blow into the fuel line. If it is clogged or pinched by the saw body, air will not flow through. You also need to check the fuel hose for rupture.
3. The crankcase, impulse hose or carburetor is not sealed. In this case, the operation of the fuel pump is disrupted and the supply stops. It is quite difficult to diagnose on your own, because... requires special equipment. It's better to contact specialists.

Stopping the supply of lubrication to the chain

As a rule, on the Partner P360S, the oil supply to the chain is rarely interrupted, because The design of the oil pump and line is quite well thought out and of high quality. But if it does stop, you need to start looking for the cause from the oil tank, or more precisely from the filter and ventilation valve.

The valve, also called the “breather,” is responsible for the flow of air into the oil tank. Works in one direction. If it is faulty and does not allow air to pass through, a vacuum is created in the tank and the oil stops flowing.

We invite you to watch the Partner P360S repair video. The video shows a major overhaul of a chainsaw (replacement of the CPG). The author talks in detail about the saw, shows how to disassemble it and install a new piston.

https://youtube.com/watch?v=2bRtgsjoXXU

Advantages and disadvantages

Partner chainsaws produced in different countries are identical in technical and operational parameters. With timely and complete maintenance, all models work out the assigned resources with a significant reserve.

• Presented in a sufficient selection of spare parts, oils, spark plugs and other consumable components, owners are given the opportunity to independently service and perform routine repairs. The budget portion of the repair fund is replenished by China, but the quality level of cheaper parts and assemblies is significantly lower.
• The list of advantages includes good build quality for its category and interchangeability of standardized parts.
• Users positively noted the absence of problems starting the engine. Despite the lack of additional equipment, chainsaws moderately adapted to cold climates can be started at temperatures down to -20°C without any problems.

There are virtually no serious design flaws. There are some complaints about the quality of the plastic, the budget life of the saw sets, and the increased consumption of chain lube.

Advantages and disadvantages of the Partner 360-s chainsaw

The Partner 360-s chainsaw has some advantages that set it apart from similar representatives of other companies. This may include the following:

• The low weight of the product, compared to analogues, and the high potential of its components provide excellent production characteristics.
• Increased operating time, which is ensured by a fuel tank with a volume of 250 ml.
• Excellent fire safety, which allows you to use Partner 360-s for a long time without fear of heating and ignition.
• The length of the tire of this model is Partner, which makes it possible to work with wood that has a large diameter.

No significant design flaws were noticed in Partner 360-s. Some complaints concerned the quality of the plastic, the consumption of chain lubrication, and the operating reserve of components and assemblies.

Saw features

The saw's gasoline engine has a power of 1520 V and is equipped with electronic ignition. To ensure safe operation, the chain has an inertial brake, which, if danger arises, turns off the engine and stops the tire in just a few seconds; you can activate the brake yourself, with your right hand during operation. In order to protect the saw operator during a chain break, the Partner P360S saw has a special catcher. This model also differs in the presence of an automatic switch that trips when the engine overheats. The unique CCS air purification system cleans the air before it enters the air filter, minimizing and greatly simplifying tool maintenance.

The Partner P360S saw is very simple to operate and operate. Firstly, to make it easier to start, the starter has an additional spring, the use of which significantly reduces the amount of force required to start the saw. Also, the resistance of the starter cable is reduced due to the fuel priming pump. The use of such a pump is also useful in that it removes remaining fuel and air from the carburetor.

With prolonged use, the saw chain may weaken slightly, so Partner P360S has a special built-in chain tensioning system that does not require the use of any tools.

The low noise level in combination with the anti-vibration system allows you to work with the tool much longer without harm to health or discomfort.

Technical and operational characteristics

Modern innovations were used in the layout of the internal equipment, which made it possible to reduce the dimensions of the tool, weighing 4.5 kg, to optimal sizes. The advantages of a two-stroke air-cooled carburetor internal combustion engine running on high-octane gasoline with a dosed addition of special motor oil are used as a compact and economical drive for the saw.

The power unit has a very moderate displacement of 35 cm3 and a power of 1.9 hp. characterized by flexible operating parameters and a reserve of torque in operating modes, which allows compensating for short-term overloads. Fuel enters the engine from an internal 250 ml gas tank.

User manual

Partner 360S comes with a user manual, by reading which you can learn how to:

• prepare the saw for the first start;
• install the bar, chain and adjust the tension;
• carry out the first launch;
• work during the break-in period;
• cut down trees correctly;
• carry out maintenance and cleaning;
• identify and eliminate faults;
• adjust the carburetor.

A separate section of the instructions for the Partner 360 saw is devoted to its safe use.

The manual also contains information about personal protective equipment that can be used during work. Wearing the right equipment will prevent injury.

Operation and Maintenance

All aspects can be found in the instructions, which can be downloaded below:

Fuel mixture for chainsaw Partner 360-s

The Partner 360-s uses one liter of AI-95 or AI-92 gasoline and 20 grams of two-stroke oil as fuel. To avoid the formation of carbon deposits, it is recommended to select high-quality oil.

Oil for two-stroke engines PARTNER Two-stroke oil Luxe 2T

Features of working with a Partner chainsaw

When working, it is recommended to follow the following tips, which will optimize the work with the Partner 360-s saw as much as possible, and also make it safer:

• Work clothes must be thick to protect against the saw in case of breakage.
• Before carrying out work, it is necessary to calculate the direction in which the tree will fall. This takes into account the direction of the wind, the slope of the soil and the tree itself.
• Clear the area of ​​the fall from bushes, undergrowth, and remove bystanders.

Maintenance rules for the Partner 360 model

• mandatory check of the condition of the chainsaw before starting work;
• Store the prepared fuel mixture for no more than 2 weeks;
• Clean the air filter every 50 hours of operation, and replace the spark plug once a month.
• tension of the chain and its lubrication for the correct operation of the chainsaw (put the chain on the bar, install the bar on the gearbox, tighten the fastening bolts, then loosen them, the chain slack should be 7-10 mm.)

The most common chainsaw breakdowns Partner

• The engine starts missing: the problem is filling the combustion chamber or spark plugs with the fuel mixture, covering them with carbon deposits. You need to unscrew the spark plug and dry the chamber using idle speed. If the Partner chainsaw becomes dirty, clean it.
• Muffler malfunctions: can be caused by the use of a low-quality fuel mixture, which subsequently results in the formation of carbon deposits. It is recommended to clean the muffler.
• Poor chain lubrication: it is necessary to check the tubes for leaks. Seal leaks with sealant or change tubes.

Description of the Partner P360S model

1. The Partner P360S chainsaw is equipped with a reliable 2 hp two-stroke engine.
2. Thanks to a special electronic ignition system, a quick start is achieved.
3. The presence of a primer in the fuel system allows the remaining air and fuel to be completely removed from the carburetor.
4. The Partner chainsaw is equipped with a high-quality OREGON saw set: bar, durable chain.
5. Complete purification of the air before it reaches the filter using the CCS system can significantly reduce preventive maintenance of the air filter.
6. Chainsaw Partner P360S differs significantly from other budget options by using higher quality components, improved design, and comfortable handles.

Chainsaw Partner P360S

The Partner 360-s chainsaw is an excellent choice when you need to carry out complex work related to cutting wood. It is equipped with a 2 hp\1500 W motor. The chain has a tooth pitch of 3.8 inches, it is tensioned on a 450 millimeter long bar.

Chainsaw Partner P360S

The main manufacturer of Partner 360-s is the Swedish plant Husquarna. You can also find chainsaws made in Russia and China. The best choice would be to purchase an original saw. They differ in a number of ways:

• Serial number on the engine crankcase, which is identical to the number specified in the instructions
• Several seals located on the casing of Partner 360-s, where the company logo is printed.
• Three-stage security hologram, which is located on the warranty sheet, instructions and box.

Malfunctions and their elimination

A significant part of operational failures is a consequence of the lack of qualified maintenance, illiterate operation, and use of tools for other purposes.

If the saw does not start, or in another case it starts and stalls, the reason for the failure may be:

• water getting into the carburetor;
• expired fuel mixture;
• air intake filter clogged with sawdust.

If the engine does not operate stably at the speed of the selected operating mode, you should ensure the quality of the gasoline itself, the cleanliness of the fuel filter and carburetor jets.

Saw attachments work in difficult conditions. In a situation where the chain is not lubricated during operation, its service life is reduced several times. If, when the tank is filled, there is no oil supply to the headset, work should be stopped until the malfunction is eliminated.

Specifications

The Partner model of the P360S series, with its own weight of 4.8 kg, is characterized by small dimensions, convenient location of filling necks and adjustment points. The design of the tool allows for servicing and routine maintenance to be carried out with minimal loss of time.

• The chain saw is equipped with a compact two-stroke internal combustion engine with a working volume of 40 cm3. The power unit running on a gasoline-oil mixture at operating speeds develops power of up to 2 hp. Fuel enters the Walbro & Ruixing carburetor from an integrated 250 ml gas tank.
• Factory carburetor adjustment provides the engine with optimal operating mode with economical fuel and oil consumption. Changing the settings of the fuel equipment is justified if traction characteristics deteriorate.
• The presence of a fuel pump, an easy start system and Zhejiang Fenglong electronic ignition, CDI ensure reliable engine starting in a wide range of external temperatures.

Changes in the operation of the power unit can be caused by sudden seasonal changes in air temperature, the use of fuel with a different octane number and other factors.

The instructions for use provide the sequence of adjustment work, as well as information on preparing the tool for operation, searching for and eliminating failures and operational malfunctions.

Basic equipment Partner P360S

All branded Partner chainsaws as standard, in addition to the saw itself, must have the following components: tires with a cover - regular and reinforced, chains - basic and for cutting hard wood, a spark plug, a warranty, 1 liter two-stroke original oil, a set of tools, container for preparing the fuel mixture.

The chain and bar are replaceable equipment. When performing various tasks, it is possible to reinstall the 40 cm or 45 cm tire.

Partner chainsaws are produced at Husqvarna factories in different countries of the world - Sweden, China, Italy, USA. To distinguish a fake from a real saw, first of all, you need to make sure that the following protection elements are present: a hologram on the saw, a warranty card, the original factory user manual, a packaging box with the designation of the country of manufacture.

Next, you should make sure that there is a special number stamped on the crankcase body and that it corresponds to the number on the warranty card. In addition, it is mandatory to have 2 branded seals with the AB Husqvarna logo. Since their production is too expensive in artisanal conditions, this factor almost 100% eliminates the possibility of counterfeiting.

Factory chainsaw kit

The standard Partner kit includes instructions, a warranty card, standard, reinforced tires, a standard chain, a chain for hardwood type RZ, a case, a measuring tank, a spark plug wrench, a hex key, a spark plug, a file, one liter of oil for two-stroke engines. Depending, the list may change.

Equipment Partner P360S

Range of application

Productive, economical and reliable in periodic use, the Partner chainsaw is designed for sawing work in private and farming sectors, in construction technologies and maintenance of forest park wood decor.

• Gasoline saws of this brand are largely adapted for working in difficult climatic conditions.
• Characterized by reliable starting at temperatures down to -20°C.
• Stable traction parameters at nominal and maximum operating conditions.

The Partner household saw successfully combines a classic layout, new developments in the field of industrial design, and special technologies for high-precision metal processing.

Equipment

The standard equipment of Partner 360 includes the function of easy chain tensioning and bar installation without the use of additional tools. The side cover has a built-in mechanism with which the tire is securely attached to the body of the chainsaw. The function is convenient, because The operator does not have to carry a set of maintenance tools with him at all times.

Another useful improvement is the manual fuel pump (primer). Due to the possibility of forced pumping, starting a cold engine is significantly easier, which means the starter’s life is increased.

The primer is not only responsible for pumping fuel, but can serve as a diagnostic tool for faults. For example, if the carburetor depressurizes, the filling capacity of the primer will deteriorate, the number of air bubbles will significantly increase, this will warn of the need for repairs.

Important! Correcting air leaks in a timely manner will allow you to avoid troubles associated with exceeding the maximum speed and scuffing of the CPG. Automatic inertia brake

At the moment, this function is found in almost all modern chainsaws, and Partner 360 is no exception. The system is responsible for instantly stopping the rotation of the chain at the moment the chainsaw rebounds

Automatic inertia brake. At the moment, this function is found in almost all modern chainsaws, and Partner 360 is no exception. The system is responsible for instantly stopping the rotation of the chain at the moment the chainsaw rebounds.

This function should not be underestimated, because... it can prevent injury or even save the life of the operator.

A starter with an additional spring that reduces engine resistance at start-up. The function is not mandatory, though. The compression on the Partner P360S is not too high, but it adds comfort and allows you to start the engine with 60% less effort.

Also, the Partner 360 chainsaw uses an anti-vibration system consisting of metal spring shock absorbers and an air pre-cleaning system to cool the engine. This system reduces the harmful impact of the tool on the operator’s hands, which adds comfort.

Reviews

In conclusion, we suggest reading reviews from users of Partner P360S.

I recently moved to live outside the city and immediately encountered the problem of maintaining the site. It was necessary to clear almost 200 meters of a fence overgrown with maple. I didn’t have a saw, so I went to the store, where the salesman advised me of several chainsaws to choose from. Shtil 180, Husqvarna 236 and Partner P360S. I chose the Partner chainsaw because... it is cheaper, similar in power to other saws offered and has a chain tensioning system without the help of keys, which the Shtil 180 only has in the Lux configuration. I cleared the area easily, the saw did a great job, I think this is a good test for it. Also, I liked the starter, which is easy to pull, and the shock absorbers. There is almost no vibration from the engine. I recommend the Partner 360 chainsaw to those who want to save a little money and at the same time have a high-quality saw for the home.

Vladimir. Tyumen. 35 years.

Purpose of P360S

Chainsaw Partner 360 is a household model of a gasoline chain saw. According to the manufacturer's recommendations, it can be used for work in a summer cottage. For example, you can use it:

• prepare firewood for heating;
• trim tree branches;
• sawing boards during self-construction;
• do figurative wood carving.

Thanks to additional attachments, which are sold separately, you can significantly expand the functionality of this chainsaw and use it as a motor drill, mower or motor pump for pumping liquids.

If you are interested in expanding the functionality of the Partner P360S chainsaw, you can read more about them on our website in the article Attachments and accessories for chainsaws.

Below is a video about the Partner P360S chainsaw. The author talks in detail about this saw, its technical characteristics, and at the same time unpacks it and prepares it for work.