How to properly install a spring on a chainsaw • EVDIRAL.RU

How to replace a chainsaw starter spring?

In order to replace the old spring in a disassembled starter, you must proceed in the following order:

Chainsaw starter repair!!! With my own hands!!!

Before installing the chainsaw starter spring, you will need to remove the mechanism clip - this should be done very carefully so as not to break the part;
Then you need to look inside the cage - in it you will see a spring wrapped around a C-shaped element. To remove the spring, fix its upper part with your finger and slightly pull the starter handle to the side;
After removing the old spring, you need to wind a new part. At the same time, try to avoid kinks and twisting of the new spring element;
To assemble the chainsaw starter spring, you will need to act as carefully as possible, otherwise one wrong movement can lead to the spare part unwinding;
After you have managed to completely insert the spring into the starter, you need to carefully fix the cage.

Chainsaw repair: replacing the starter spring

Do-it-yourself chainsaw repair - replacing the recoil starter spring.

a set of screwdrivers or a special tool, which is included with the tool by the manufacturer;
a rope that will be used as a replacement for a broken cord if necessary.

A large amount of black carbon deposits on the spark plug indicates problems with the engine.

Before proceeding directly to repairing the starter and identifying the causes of malfunctions, it is necessary to remove it from the tool body. To do this, you need to unscrew several screws holding the side cover to which the starter is attached. This is done with a screwdriver or a specialized tool.

After the lid is unscrewed, it is turned over and inspected. Next, unscrew the screw that secures the starter. After this, the clamp and spring are dismantled for a smooth start. Now the pulley on which the cord is wound is accessible for removal. Once the knot on the rope is undone, it can be pulled out from the pulley and replaced with a new one. Provided that the loss of starter functionality is associated with a break, this may be enough to eliminate the breakdown. However, the remaining parts that make up this element of the chainsaw should be carefully inspected.

When inspecting the starter components, the following malfunctions may be identified:

How to assemble spring of starter

The pulley may be damaged. There may be cracks or tears, or damage to the back. How to correctly insert the trimmer starter spring. How to wind the starter spring of a power tool. how to install a spring in how to wind a starter spring chainsaw repair. As a result of these problems, the tool cannot perform the job.
Damage to the soft start spring. the spring itself may be mechanically faulty , or there may be defects in the place where it is attached. The weakest point of this element is precisely the fastening point and the tip of the spring that is inserted into it.

If faulty or partially damaged starter parts are found, they must be replaced with new ones. how to wind a starter spring, how to properly repair a chainsaw starter. In this case, the new elements must correspond to the saw model being repaired.

After completing the repair, you need to properly reassemble the starter.

The pulley is installed on top of the spring. In this case, it is necessary to check how much they adhere to each other. To continue the repair, it is necessary to wind the pulley. how to wind a spring and how to wind a chainsaw starter rope. everything is as usual. How to make a starter on a chainsaw yourself? How to bend the spring on a chainsaw starter? How to wind a spring and how to wind a chainsaw starter rope. Everything, as usual, is simple and easy, and most importantly. This must be done in such a way that when it rotates, it pulls the cord into the starter. It is enough to make 3-4 turns to give the required voltage. First, the rope is threaded through the hole in the lid of the chainsaw.

How to install a spring on a chainsaw starter?

Fitting the starter spring into the correct groove is not an easy task even for an experienced user. First, the spring should be twisted to its previous diameter and installed in the cavity of the drum hub. The outer end of the spring is fixed by the limiting protrusion, and the outer end should be positioned opposite the hole in the lock using a screwdriver. Using a screwdriver, align the loop at the inner end of the spring with the hole, after which the disk is lowered. By rotating the disk, check whether the ratchet pawl is in place. Next, the ratchet itself is assembled.

READ How to Remove Carburetor From Husqvarna Chainsaw

After installing the spring, it is necessary to adjust its tension. spring is twisted around it . After removing the slack, it is better to wind the spring an additional few turns to ensure the required tension on the part.

Starter replacement

Procedure for replacing a chainsaw starter:

Remove the assembly from the tool body.
Unscrew the mounting bolts and remove the side cover.
Unscrew the mounting screw that secures the starter.
Remove the clamp and spring mechanism of the starting system.
Remove the pulley with cord.
Replace all worn and damaged elements.
Wind the pulley.
Install a new starter.
Reinstall the pulley with cord, clamp and spring.
Screw the side cover and install the unit on the chainsaw body.

Before installing a new starter, it is recommended to inspect it for defects, check the quality of assembly and the presence of a guide bushing.

Spring repair

Procedure for repairing the starting system spring:

Remove the starter from the tool body.
Remove the protective cover.
Wind the cord around the end of the pulley to prevent the mechanism from turning.
Thread the second end of the cord into the hole in the protective cover.
Pull the cord 17-20 cm to check the rotation of the spring mechanism pulley.
Check the operation of the spring after pulling and releasing the mechanism.
Unscrew the pulley circle from the side of the generator, removing the 3 mounting bolts.
Remove the pulley and cord.
Check the condition of the parts for wear, damage and breaks. If the spring break is small, then the defect can be eliminated by welding.

Basic malfunctions of the trimmer starter

It is not difficult to determine the cause of the breakdown of the trigger device. There are several main options:

broken cord (rope);
when the spring breaks or becomes disengaged.

These parts are shown in the photo below.

It may happen that the starter mechanism is accidentally broken. The consequences will be disastrous if a broken rope is wound around the flywheel of a running internal combustion engine: then the spring will burst and the pulley will break. But such cases when a complete replacement of the starter assembly is required are extremely rare. In most cases, to repair the mechanism, it is enough to install a new spring or replace the cord.

Typical breakdowns and repairs of a chainsaw starter

The appearance of various starter malfunctions leads to the inability to start the chainsaw. The most common starter failures include:

The starter pulley has completely burst or has cracks;
The spring burst ;
The starter cable is broken.

To fix each of these faults with your own hands, you will need certain tools. You must have a set of screwdrivers and a spare cable with you. You need to remove and inspect the starter for a chainsaw in the following order:

To find the cause of the breakdown, the starter from the chainsaw will need to be removed. To do this, you need to unscrew the screws with a screwdriver that hold the protective cover with the starter attached to it;
After removing the cover, you must carefully unscrew the screw that secures the starter to the protective cover;
Then you need to try to start the starter smoothly - to do this, remove the spring and clamps from it;
Next, the reel with cable is removed from the starter for inspection.

As a result of the inspection, you may discover a number of typical faults. These include:

Various damage to the pulley in the form of breaks or cracks, mainly in the rear part of the part - they interfere with the normal operation of the entire starter;
the spring itself may be faulty , but also the place where it is fixed - this is the most vulnerable part of the spring;
The starter flywheel pawl is damaged.

In any case, any faulty part must be completely replaced with a new part.

Typical faults

If the operating rules are followed and used carefully, a chainsaw can serve the owner for many years. However, minor malfunctions and problems still arise. Among the most common breakdowns are problems in the ignition system and starter problems.

broken or burst pulley;
break of the starting cable;
broken starter spring.

The most common tool failures include the following:

problems in the ignition system;
stopping the chainsaw while cutting;
loss of power during operation;
wear of some structural elements of the chainsaw (brake band, drive sprockets, anti-vibration parts);
problems in the fuel supply system;
starter related problems.

In addition, it is necessary to carry out a visual inspection of the chainsaw before starting work and take preventive measures. These include lubrication of the chain, control of the amount of fuel mixture, as well as the presence of the required amount of oil.

The spark plug is unscrewed to check its condition.

Each of the faults is eliminated using its own technology. For example, repairing the fuel system of a chainsaw should begin with inspecting the corresponding filter. After this, check the correct adjustment of the carburetor, which is carried out using screws. The gaps must be set in strict accordance with the manufacturer's instructions, which must be included with the chainsaw.

The gaps must be set in strict accordance with the manufacturer's instructions, which must be included with the chainsaw. Repair of the ignition system includes inspection of spark plugs. If heavy carbon deposits, changes in clearance or other visible damage are detected, this element must be replaced.

How to assemble a starter on a chainsaw?

After replacing the faulty elements of the starter, it is time to reassemble it. In this case, maximum accuracy must be observed, since the slightest discrepancy can lead to breakdown of the trigger mechanism. Assembly of the unit must be performed in the following sequence:

The standard cable will need to be threaded into the factory hole of the reel. There is no need to wind the cord;
Next, you will need to insert the coil into its base location. At this stage, many beginners make a common mistake. There are 2 slots on the surface of the coil. The standard coil spring hook should fit into one of them. To do this, the coil will need to be installed in such a way that it fits tightly into its original place, and the existing hook fits exactly into the slot. Correct installation must be checked by turning the coil clockwise until resistance appears;
Then you need to install a device for easy starting of the chainsaw. In this case, the protrusion of the latter should be located in the recess of the installed coil;
After this, you will need a screw and washer to secure the device;
Next, the second end of the cord must be tucked into a special outlet hole;
The next step is to thread the cable into the starting handle. For this purpose, you will need to tie a medium-sized knot at the end of the cord. If it is too small, the cable will slip, causing it to quickly wrap around the trigger drum;
Then you will need to release the loop inside the starter. Immediately after this, you should begin to rotate the trigger mechanism in the direction of the clock hand. There is no need to wind the cord. Next, you will need to fix the reel with your hand and pull the loop outward by the handle;
After this, you need to check the operation of the trigger mechanism;
If the unit is working properly, all that remains is to install it on the tool and secure it with three screws.

Repairing a starter is not a difficult procedure if you follow the correct procedure. Typically, replacing the starter cord will take no more than 20 minutes. The main thing is to correctly position the pulley and drum in relation to each other. Otherwise, the trigger will not work.

Tips from the professionals

It may be necessary to make 2-3 turns to accurately orient the holes in the housing and the rope fixation channel.

Tips for repairing a chainsaw starter

In order to prevent the cord from slipping out of the pulley, it is necessary to tie a knot whose diameter exceeds the hole in the housing. If there is no wear (damage) to the spring, it is installed first when assembling the chainsaw starter. A pulley and starter clamp are mounted on top of it, preventing the mechanism from skewing during rotation.

As it turns out, repairing a chainsaw starter with your own hands does not require any special skills or tools. However, restoration of the starting mechanism must be approached responsibly and preventive inspections must be carried out from time to time.

Chainsaw starter device

As standard, the chainsaw starter consists of a number of parts.

coil;
cable;
frame to which the return spring ;
pen.

A protective cover is installed over all starter elements. The initial operating principle of most trigger mechanisms is also almost the same. In a special groove in the chainsaw body there is a handle that holds the cable. When the handle is raised sharply, the latter is understood. At this moment, the ratchet is activated, which transmits the force through the drum to another splined drum located on the motor shaft.

When the standard cable is pulled, the chainsaw motor shaft begins to rotate, which leads to compression of the existing fuel mixture, located at this time between the cylinder head and the standard piston.

As the cylinder volume of an internal combustion engine increases, the amount of consumed fuel mixture, which is required for its future ignition, simultaneously increases. Accordingly, the operator of a powerful saw needs to make more jerks than the owner of a household tool with low power. To increase the speed at which the drum returns to its original position, manufacturers of powerful chainsaws use elastic return springs.

READ How to Properly Start a Stihl 180 Chainsaw Video

Chainsaw starter repair

When the chainsaw is started frequently, some parts of the starter are constantly subjected to dynamic loads. As a result, the cable may burst, several teeth of the ratchet may crumble, and the shaft will rotate at a much lower speed. Therefore, inspection and even repair of the starter are operations that are sometimes carried out several times a season.

Spring recovery

The most common case of failure is associated with the chipping of the fastening ear of the main ribbon spring, which rewinds the cable. It is not necessary to search for and buy a new spare part, since the procedure requires a minimum of time and tools. You only need 2 things: a fire source (gas burner or stove) and pliers.

Carefully remove the spring from the housing. You can pry it off with a slotted screwdriver.

In place of the broken ear, you should make a new one by making an ordinary bend of the tape. To prevent the metal from bursting, before bending it must be heated red-hot and bent until it cools (it is better to do this directly over the fire).

The shape and size of the bent part must be identical to the original in order to fit snugly against the protrusion of the stopper. How to thread a spring into a chainsaw starter and save your nerves is described below. Wait until it cools down completely before proceeding with installation.

Repair procedure

The operating features of the starter imply a sharp and rough impact, which sooner or later affects itself in the form of breakdowns. Fortunately, there is nothing special to break in this mechanism and the instructions below cover all possible causes of problems. Starting with how to restore or how to insert a spring into a chainsaw starter, and ending with installing pawls and removing the flywheel. Step-by-step guides, sequentially, for each problem.

How to install a chainsaw starter spring

Basic dexterity and standard manual dexterity, combined with simple technology, will reduce time costs, allowing the operation to be performed quickly and almost effortlessly. Installation of the return spring begins by fixing the ear on the notch, in a counterclockwise direction (looking at the inside of the spring housing).

The tape is inserted gradually, layer by layer. The thumb of the right hand holds the already placed part of the spring, while the finger of the left hand places a new section. Having inserted about 1/3 of the circle into the body, the tape is pressed with the thumb of the left hand, the right one is brought to it and the cycle is repeated. The entire installation process takes no more than a minute.

It’s even easier to insert a new spring purchased as a spare part for the starter. It may be in a fixing winding, which is gradually removed during installation. The already twisted element is simply inserted into the body. The simplest option is a ready-made kit with a ribbon spring in the housing, which are installed in place of the old elements in one movement.

Repairing a chainsaw starter: instructions for each part (photos and videos)

Replacing the cord

Cases of breakage of the handle cable are quite common and characteristic of both Chinese models and branded manufacturers. Since this connecting element is subjected to severe stress and periodically breaks, the replacement process is extremely simplified. First of all, you should decide how long the cord on the chainsaw should be. Depending on the size of the drum and the diameter of the cable, the value is in the region of 120 – 140 cm (always with a small margin). Having prepared a suitable piece, you can take a Phillips screwdriver and start replacing.

Remove the starter from the chainsaw and unscrew the central screw on the ratchet.

We take out the drum and remove the old cord.

We pass a new cord through the hole from the inside of the drum groove (for convenience, the ends can be melted with a lighter).

We pull the end out of the hole by ≈ 10 cm and tie it in a knot so that the cable does not fly off.

In a special recess under the drum, we place the knot and the remaining part of the cable. To prevent it from resting on the spring housing, it is advisable to leave about 1 cm.

We install the drum in its place, aligning the spring with the ear, and press it with a screw and washer (do not wind the cord).

We pass the opposite part of the cord through the starter body and the hole in the handle, after which we make a locking knot at the end.

The cord is wound by a spring. Simply pull the cable slightly from the hole in the drum to its edge, and holding it at this point, rotate the drum clockwise. The spring tenses, and when released, it winds the cable itself. We repeat the procedure until the handle is pressed tightly against the body.

Types of gasoline saws

Depending on the type of use and, accordingly, the technical characteristics that different models of chainsaws have, they are qualified as follows:

Household - designed for short-term work and performing simple operations. They are light in weight, compact in size, easy to maintain and operate. The duration of use of such a tool is up to 1.0 hours per day.

Semi-professional – used in various fields of construction, in various spheres of human activity. They are a universal type of this type of tool. Duration of use – up to 10.0 hours per day.

Professional – used for industrial volumes of lumber production, long-term use (up to 16.0 hours per day) in a year-round operation cycle.

Chainsaw starter device

Carrying out diagnostics or repairing a tool is much easier and more effective if you understand the principle of its operation. To facilitate and speed up the process of restoring the starter, it is recommended to know what it consists of and how it works. The general picture is presented below in an extremely clear and concise manner. Let's start with the main components of the mechanism:

The starter cover is the basis for securing parts and protecting them. Necessary for internal circulation of air forced by the rotation of the flywheel, which ensures engine cooling.
The handle is an external element with a fixed end of a cable wound around a drum and unwinding it when pulled out of the body.
Ribbon spring - returns the drum to its original position, winding the cable back.
Spring housing - provides insulation for the band spring and secures its end to prevent twisting when tensioned.
The starter drum is the central element of the mechanism, interacting with all parts. Has a hole for fixing and a groove for winding the cable.
spring - plays an auxiliary role, adding a few turns after the cable is fully pulled out. It is not present in all models of chainsaws and may have a band or screw shape.
Ratchet - the outer part of the drum, with hooking protrusions that rest against the flywheel pawls when the lever is pulled out.
Pawls are spring-loaded thrust elements that transmit rotation from the drum to the flywheel and crankshaft. The precise shape and location ensure confident engagement of the ratchet teeth when pulling the cable, and free movement in the opposite direction when reeling in.

Having examined the main components and their functional purposes, we can shed light on a more pressing topic and analyze the principle of operation of the chainsaw starter along the chain of interactions of the mechanism parts. The starting process begins with pulling out the handle, which pulls out the cable, thereby unwinding the drum with the ratchet. The teeth of the ratchet rest against the pawls attached to the flywheel and transmit rotation to the crankshaft.

READ How to Adjust the Carburetor on a Husqvarna 137 Chainsaw

In one second jerk of the handle, the flywheel and shaft make about 4 revolutions, activating the entire saw system. During this instant, a fuel-air mixture is supplied to the combustion chamber, and the spark formed in the coil ignites it, pushing away the piston, which begins to rotate the crankshaft from inside the engine. In most cases, a serviceable, cold saw starts with 3-4 jerks, and with a lighter start it starts even faster.

Replacing the ratchet

The main element that transmits rotation to the flywheel is subject to serious wear at the contact points. The teeth of the plastic ratchet (pulley), resting on the pawls (especially iron ones), tend to chip or wear off, seriously complicating the starting process. The second problem relates to the easy-start ratchet, which is connected to the drum through a spring, which can break off at the attachment point. The ribbon spring can be restored by following the instructions outlined above, but if the screw spring is chipped, the structure will have to be replaced. How to remove and install the chainsaw starter ratchet is shown below:

We remove the starter and unscrew the main fastening screw of the structure with a washer.

If the starter pulley for a chainsaw is non-separable, then replacing it will require removing the cord. Simply untie the knot on the handle and pull it through all the holes (handle, body, drum). If the ratchet is dismountable and the drum does not require replacement, we simply carefully separate them so that the spring does not fly out.

We fix the pulley with a screw and washer and install the starter on the chainsaw.

Algorithm for replacing a piston chainsaw

If the time has come to replace the chainsaw’s CPG, you need to know that for each specific model there is an individual algorithm of actions. To facilitate disassembly/assembly work, it is necessary to prepare a spark plug wrench, a large flat-head screwdriver, a hammer, a compressor for cleaning unit parts, and a set of open-end and socket wrenches. Regardless of the manufacturer and design features of the model, before removing the chainsaw cylinder, the following work must be done:

Removing the top protective cover;
Unscrewing the spark plug;
Removing the side cover;
Using a large flat-head screwdriver, remove the stoppers from the shock absorbers;
We place a cord in the spark plug channel to secure the crankshaft and unscrew the clutch and flywheel nut;
Removing the chain drive sprocket;
We remove the carburetor with the air filter;
Remove the ignition module and exhaust system.

After removing the power unit from the base, unscrew the pan and remove the crankshaft with the piston from the cylinder. Using tweezers or a screwdriver, remove the piston pin stoppers.

Before dismantling the piston, it is necessary to remember its location in the cylinder, so that in the future you do not waste time re-disassembling and reassembling the power unit.

Sealant for fixing the chainsaw tray

Before starting assembly, it is necessary to clean the parts and components of the unit from dirt, sawdust residues, and dust using compressed air, rags and other means. The first stage of replacing a piston chainsaw is to install a piston on the crankshaft. We fix it on the connecting rod with a steel pin included in the delivery set of the CPG. In order to prevent the locking rings from accidentally falling out, it is recommended to install them with the cut down. Next, we install the compression rings on the piston, but due to their fragility and fragility, this operation must be approached with the utmost care. To prevent scratches, the piston must be lubricated with oil before installing the piston into the cylinder. Before installing the crankcase (pan), you will need to degrease its mounting surface and apply a layer of heat-resistant sealant. We assemble the chainsaw in the reverse manner to the algorithm described above.

Often, replacing the chainsaw piston, crankshaft and compression rings solves problems with idling and problematic starting of the internal combustion engine.

Replacing a STIHL 180 Piston Chainsaw Video

How to change the piston on a STIHL 180 chainsaw

The main malfunctions of the STIHL ms 180 chainsaw are related to the piston group. Let's look at the main reasons why the piston needs to be changed. Let's give a description of the piston

and the method of its replacement.

IMPORTANT. An experienced electrician leaked the secret of how to pay half as much for electricity, a legal way

Typical breakdowns and repairs of a chainsaw starter

The appearance of various starter malfunctions leads to the inability to start the chainsaw. The most common starter failures include:

The starter pulley has completely burst or has cracks;
The spring burst ;
The starter cable is broken.

To find the cause of the breakdown, the starter from the chainsaw will need to be removed. To do this, you need to unscrew the screws with a screwdriver that hold the protective cover with the starter attached to it;
After removing the cover, you must carefully unscrew the screw that secures the starter to the protective cover;
Then you need to try to start the starter smoothly - to do this, remove the spring and clamps from it;
Next, the reel with cable is removed from the starter for inspection.

As a result of the inspection, you may discover a number of typical faults. These include:

Various damage to the pulley in the form of breaks or cracks, mainly in the rear part of the part - they interfere with the normal operation of the entire starter;
the spring itself may be faulty , but also the place where it is fixed - this is the most vulnerable part of the spring;
The starter flywheel pawl is damaged.

In any case, any faulty part must be completely replaced with a new part.

Malfunction of unspecified category

In some cases, owners of chainsaws have to solve more complex problems to fully restore the functionality of their cutting tool.

The chainsaw does not develop full power

In addition to the problem discussed above with a lack of gasoline or air entering the cylinder, the cause of low power may be a clogged muffler.

Carburetor depressurization and nozzle blockage

Over time, the screws holding the carburetor cover in place can become loose or the gaskets can become unusable. A clogged filter or improper replacement can lead to clogged injectors. All this also negatively affects the operation of the chainsaw and shortens its service life.

Chainsaw won't idle

It often happens that after long-term transportation and constant use, a chainsaw refuses to idle smoothly. As a rule, this problem is eliminated by adjusting the carburetor.

You can learn how to properly debug the carburetor from this video:

If the carburetor is tuned like a clock, then you need to check:

Fuel system. It makes more sense to start with the fuel pump.
Muffler. There is a high probability that due to the abundance of accumulated soot, the engine cannot function normally.

Chainsaw loses power under load

If during operation the power of the saw disappears somewhere, then the problem should be looked for in the following places:

In the muffler. It, as you already understood, tends to get clogged.
In a clogged fuel filter.
A poorly functioning fuel pump.

The design and principle of operation of a chainsaw starter

Most well-known manufacturers of chainsaws equip their products with starters that work on almost the same principle. Its essence is as follows: in the groove of the saw body there is a handle through which the cord is passed. When the handle is raised sharply, the cord is also pulled out, which engages the drum, which is located in the ratchet mechanism. Through this, a drum with spokes, which is located on the shaft, is activated. During this, the crankshaft makes a couple of revolutions, which leads to compression of the fuel mixture, which at this moment is between the cylinder head and the piston. When the handle is lowered, on the contrary, the ratchet and the pins lose their contact, which leads to the shaft stopping.

As the power of the chainsaw increases, the amount of fuel mixture increases, which must ignite when the chainsaw is started. In this case, to start the engine, it is necessary to increase the number of pulls on the starter cord. To speed up the return of the drum mechanism, manufacturers use a special steel starter return spring , which has excellent elasticity. To make starting a chainsaw easier, leading brands also use other methods:

Preliminary enrichment of the fuel mixture using a separate damper;
Installation of an automatic decompression valve, which reduces the pressure inside the chainsaw cylinder;
Installing a primer designed to pump fuel before starting the engine.

The use of one of these technologies significantly facilitates starting and extends the service life of the starter, which is especially noticeable at low temperatures.

How to replace a chainsaw starter spring?

In order to replace the old spring in a disassembled starter, you must proceed in the following order:

Before installing the chainsaw starter spring, you will need to remove the mechanism clip - this should be done very carefully so as not to break the part;
Then you need to look inside the cage - in it you will see a spring wrapped around a C-shaped element. To remove the spring, fix its upper part with your finger and slightly pull the starter handle to the side;
After removing the old spring, you need to wind a new part. At the same time, try to avoid kinks and twisting of the new spring element;
To assemble the chainsaw starter spring, you will need to act as carefully as possible, otherwise one wrong movement can lead to the spare part unwinding;
After you have managed to completely insert the spring into the starter, you need to carefully fix the cage.

Sources:

https://zemlyconsalt.ru/pily/kak-ustanovit-pruzhinu-startera-benzopily.html https://instrumentoria.ru/156-remont-startera-benzopily-svoimi-rukami.html https://sadovij-instrument. ru/benzopily/starter.html